Power Products Thread....any and all info welcome.

[ray benson]

Looks very similar to the Tecumseh carb on page 2 of the attachment

 

[Matt Hogden]

I have recently acquired a few Power Products powered saws. For some reason there is little to no info on the web about them, other than they were used in saws, karts, mowers and such. They are dead nuts simple engines, that make good power, but there seems to be a lack of interest in the general population of chainsaw idiots such as myself. Not real sure why though??

So, what models you got, and what info do you have on them?

So far I have acquired a Wards with an AH81 (131cc), a Mono with the AH58 (95cc) and a couple David Bradleys with the AH47 (77cc).

I have 2 Monos with the AH58

Sent from my SM-G930F using Tapatalk

 

[Den]

I have a Power Products Tecumseh Mono 2-16 listed in the trading post here on AS. It has the AH-47 engine. I thought it was locked up, but after putting a wrench on the sprocket nut I discovered it turns. It will be going on Ebay soon.

 

[peter92]

Heres my second mobilco Big 10 Ah81 131cc chainsaw in Australia
just wondering what is the longest bar i could put on it and would any one have part number of the bars please
i have the yellow tank but needs pulling apart and redoing as it leaks

Peter

 

[peter92]

Heres an Advert from Australia about the MOBILCO SAW RANGE

 

[sawnami]

A David Bradley, Mono, and Barker. All AH-81's.

Sent from my SM-N950U using Tapatalk

 

[peter92]

Hi Guys , What saw has the AH82 engine 135cc
Ive got one with AH81 130.7 cc
Chasing just an engine
Peter

 

[ncrile]

Hello all!
Jumping in this dusty thread in search of info. I have an old Trams 3DT with a Power Products AH47 motor. I'm trying to source seals. they are unlike anything I've ever seen. They are all rubber (no metal frame) they are slightly conical on the inside and they have a minute wiper.

ID = 17mm or 43/64"
OD = 22mm or 55/64"
Thickness = 3mm or 1/8"

Is it a seal? square edged oring? Shaft wiper?
Does anyone know where to get them?
Any help would be great

 

[2broke2ride]

I found some a few years ago on ebay. Ley me see if I can come up with a part number. These are the ones that have a metal washer and snap ring holding them in, correct?

Sent from my SM-G950U using Tapatalk

 

[ncrile]

I found some a few years ago on ebay. Ley me see if I can come up with a part number. These are the ones that have a metal washer and snap ring holding them in, correct?

Sent from my SM-G950U using Tapatalk

YES! exactly!

 

[2broke2ride]

510105 is the number I have. A quick ebay search came up with this. Kinda pricey, I was able to just buy the seals.
https://www.ebay.com/itm/333487318867

Sent from my SM-G950U using Tapatalk

 

[ncrile]

510105 is the number I have. A quick ebay search came up with this. Kinda pricey, I was able to just buy the seals.
https://www.ebay.com/itm/333487318867

Sent from my SM-G950U using Tapatalk

Hey, thank you 2 Broke2Ride! !!!!!!!

That's a big help! Thanks also for the ebay link, this old saw has already cost me an arm and a leg trying to get her going. I've never spent that much for seals. OUCH!

I could not find an IPL with the part numbers. Did you ever get yours installed? So much knowledge on this site!

 

[2broke2ride]

I replaced 1, the ones in the picture are the ones I have. I bought 3 at the time. I ended up having to take a dremel and grind a relief in the outer lip so I could get behind the snap ring with a pick.

Sent from my SM-G950U using Tapatalk

 

[ncrile]

I replaced 1, the ones in the picture are the ones I have. I bought 3 at the time. I ended up having to take a dremel and grind a relief in the outer lip so I could get behind the snap ring with a pick.

Sent from my SM-G950U using Tapatalk

Great Idea!

I sharpened an old nail punch and tapped it in. Yes, it damaged the washer. Live and learn.
I put an offer in on the Ebay listing. I feel all slimey and want to take a shower.

 

[sawnami]

You can get much better deals if you take your time. I picked up two on eBay a few days ago.

Sent from my SM-N950U using Tapatalk

 

[ncrile]

You can get much better deals if you take your time. I picked up two on eBay a few days ago.

Sent from my SM-N950U using Tapatalk

Yeah, I broke my cardinal rule on this one. FOMO got the best of me. I got a better deal than the original, but still not a good one. Thanks for the perspective. I can’t play the game if I can’t afford it. When I hear it from the Mrs, she can’t understand. It hits home to hear it from the folks here. But it is so true.
Be patient.

 

[elioselectric]

Anyone know the part number for the AH47 1/16" thick piston rings, not the more common 3/32" like in the David Bradley saws. The thinner rings are in the Lombard L50, piston ported jug. 2 inch bore. Thanks

 

[67L36Driver]

Shop this EBay seller.

https://ebay.com/usr/dandrikop
Shop his rings by bore x thickness & gap/end condition.

And, 1.5mm is close enuf to .062”.

[emoji106]

I bet 51mm x 1.5mm will work with a touch of end filing.

 

[Kino B.]

Hello gentlemen, I recently acquired a Mono AH81 and I’m looking for a rebuild kit for this carb. Does anyone have a part # or source for this? Thank you!

 

[ncrile]

Try discount marine parts. They sell carb kits for many OLD carbs.