I'm thinking it would be possible with alitte drilling to adapt a D007 bar to my super 754 ?
If I'm wrong please let me know.
If I'm wrong please let me know.
Remington Chainsaws(including Mall chainsaws)
- Thread starter wampum
- Start date
Help Support Arborist Forum:
.404 sthil chipper chain , currently.98% probability it runs 7/16”.
Good luck finding enuf for a loop much less full skip.
Either way, 42” should be no problem.
Longest I have is 31”.
It almost beat me! But I got the clutch changed to a rim sprocket. 
Finally finished modifying a 36" Husqvarna bar for the 754 and ordered micro chisel skip .404
I made a few cuts and for thumb action oiler it works pretty well. I will probably make an outside bar plate for it later.
The last picture is my new socket that fits (ONLY) a Remington super 754 chainsaw ! After I made my cuts I noticed the plug was loose so out came the grinder.
I don't know how the loose plug might of affected the cut but definitely wasn't helping compression.
Had a similar problwm with my Pro 88. I converted it to a Homelite 1050 sprocket with some machined bushings.
Those wanting an alternative to 7/16” chain.
Oregon 10619 Drum .404 7T Rim Sprocket Bushing Washer Remington 760 770 660 65 https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.com/ulk/itm/163895906357
Way past my budget. [emoji2960]
Oregon 10619 Drum .404 7T Rim Sprocket Bushing Washer Remington 760 770 660 65 https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.com/ulk/itm/163895906357
Way past my budget. [emoji2960]
I believe that there's a few used ones out there, I know I saw a parts seller online with a good used one but it didn't have the bronze bushing.
That is the exact one I just put on my super 754 and it is convenient. The budget for that saw was pretty flexible because of the fact I paid 25$ for the saw and it didn't require anything to run.
That looks a lot like what I did to my Pro 88. I had the drum and clutch already. I used an aluminum/bronze alloy. It's quite hard and has held up well in other similar applications.
Attachments
I have two of the Oregon 10619 kits I’ll never use.
Shoot me a PM if interested.
Undercut the evilbay seller by a wide margin I will. [emoji106]
And, yes, high silicon bronze can be as hard as steel.
Shoot me a PM if interested.
Undercut the evilbay seller by a wide margin I will. [emoji106]
And, yes, high silicon bronze can be as hard as steel.
Ok first time taking apart the Remington super 754 , does the ignition components look normal?
Wico. You B in luck. No Bendix-Scintilla crap coil.
I've not seen the Bendix ignition on a Bantam series yet. Maybe the very earliest Bantam models. I don't know.
I take it nothing looks out of order?
Doesn't look to be. FYI, coil timing is as simple as lining up the 2 legs of the lamination with the 2 marks on the case.
Chris B.
Thanks , ran 2 tanks through her today and she's running strong ....then gets hot and pukes gas out the muffler, its got a new carburetor on it so I'm thinking it's the gas cap vent?
Jimtom
ArboristSite Lurker
First post here!!! This just showed up at my house today.....https://www.ebay.com/itm/Vintage-REMINGTON-LOGMASTER-Chainsaw-Chain-Saw-Model-49300/193156713084?ssPageName=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649
Talked her down to $35 plus shipping. Am I crazy??? We'll have to wait and see. The 1st thing that scared me is it appears to have been helicoiled in the plug hole. I had a 14mm plug laying around and it screwed in tight so that's good. The gas tank had an acorn in it and the air filter is upside down. Needless to say I'm up for a challenge once I get the corn all picked. What do you guys think? Wall hanger or will she come back to life?
Talked her down to $35 plus shipping. Am I crazy??? We'll have to wait and see. The 1st thing that scared me is it appears to have been helicoiled in the plug hole. I had a 14mm plug laying around and it screwed in tight so that's good. The gas tank had an acorn in it and the air filter is upside down. Needless to say I'm up for a challenge once I get the corn all picked. What do you guys think? Wall hanger or will she come back to life?
Definitely not a climbing saw.
I've been fooling with these lately. Got a group picture before putting them away.
Similar threads
