Remington Mighty Mite Help

[astnmacgto]

Ohhh, both of mine had a wing nut I believe, at least the weekender did

 

[Ginger15]

Yeah, thats the only filter I can seem to find, the kinds with wing nuts. Mine is a tad different.

 

[67L36Driver]

I've not had mine apart at all. Just add fuel and oil and run.

 

[Ginger15]

I've not had mine apart at all. Just add fuel and oil and run.

you run your saw without an air filter?

 

[Ginger15]

Anyone got a spare 10" bar? I can only find a 12". I might have to go with that. My pole saw bar(that came with it) doesnt accept a tension nut and a several drill bits have not made a dent.

 

[67L36Driver]

Actually I haven't looked. There may be one in there or not.

 

[Ginger15]

Would you mind showing me the bar mount pattern? So I can see how far apart the spaces are? Or maybe take some measurements if you aren't too busy?

I'm looking at a 12" bar on ebay, the slot is the right width, but the two holes center to center are 2cm, or 20mm. Which I think won't line up correctly on my saw. It is a Remington bar though. I'd like to compare it to yours.

 

[Ginger15]

http://www.ebay.com/itm/262814697450?_trksid=p2060353.m1438.l2649&ssPageName=STRK:MEBIDX:IT

Will this sprocket fit? 1/4" chain around here is almost double what a 3/8" chain is. So I'm tempted to swap to a new sprocket.

 

[67L36Driver]

1/4" slot, 1/2" center of slot to center of dog hole.

 

[67L36Driver]

A Homelite XL, XL-2 and Super 2 bar will work fine.
Homie bar on right.

 

[Ginger15]

Thank you, this is the bar I am looking at. I think it will fit? 7mm slot for the bar stud. About 3/4" center to center for the two stud holes.

Any help on the sprocket?

 

[67L36Driver]

I looked at the IPL's and sprocket drums (1/4" & 3/8" LP) have different part numbers between Mighty Mite Bantam and the Yardmaster, Mighty Mite 100 types.

It would be a crap shoot really.

Message the evilbay seller.

 

[Ginger15]

Waiting on a reply from the seller.

What is the P/N for the 3/8 for the Bantam model?

I found this image while searching. It says it should fit?

It says Montgomery Ward 24002-A, mine is an 24003-A however.

 

[67L36Driver]

The IPL's don't say weather 1/4" or 3/8". [emoji37]

Get on Chainsawer.com and download the respective IPLs.

I did that today as I didn't need them until now.

 

[67L36Driver]

Thank you, this is the bar I am looking at. I think it will fit? 7mm slot for the bar stud. About 3/4" center to center for the two stud holes.

Any help on the sprocket?

Is that a sprocket nose bar?

It could be for a Remy pole saw. Common they are but they don't have a hard tip and will fail in short order. Chain speed is much higher on a gasoline powerhead.

 

[67L36Driver]

That should work fine.

A bit spendy but.......

 

[Ginger15]

I have the IPL for the mighty mite already. It's how I tracked down all the parts I needed. None have much helpful info on the sprocket.

I have a question in to another seller about the diameter of the sprocket and the bearing hole. Will see if it matches up with my saw.

 

[Ginger15]

That should work fine.

A bit spendy but.......

I found the oregon part number on evilbay for under 9$. Not bad at all.

 

[Ginger15]

Is that a sprocket nose bar?

It could be for a Remy pole saw. Common they are but they don't have a hard tip and will fail in short order. Chain speed is much higher on a gasoline powerhead.

No, its not a sprocket bar. I will keep looking for a bar then. Mac bars seem to fit. The A318 pattern. The oil hole is just a tad low but it will still flow to the chain.

 

[67L36Driver]

No, its not a sprocket bar. I will keep looking for a bar then. Mac bars seem to fit. The A318 pattern. The oil hole is just a tad low but it will still flow to the chain.

Drill press fixes that issue.