Sure is quiet in here....do I need to start a fight?

[Stihl 041S]

Laying in the sun?

I could lie on the sidewalk.

On the heating pad till the back quits complaining.

I don't mind the heat.

But at work you are in no burn clothing and you are on a machine making steam all night.

Air doesn't move much. Even with fans.

Cools down around 1:00 am.

 

[IEL]

Hey john, any thoughts on those hutchins hustler board sanders?
They look really handy for body work. I dont think my compressor would have any issue running one.

I have my eye on an old piston compressor pump, two cylinder, 18 inch flywheel with 4 inch flat belt drive. It has a 1 inch twist lock fitting on it. Probably close to 30 cfm. Hook it up to a wisconsin engine, and I would never worry about lack of air again.

 

[tbone75]

Hey john, any thoughts on those hutchins hustler board sanders?
They look really handy for body work. I dont think my compressor would have any issue running one.

I have my eye on an old piston compressor pump, two cylinder, 18 inch flywheel with 4 inch flat belt drive. It has a 1 inch twist lock fitting on it. Probably close to 30 cfm. Hook it up to a wisconsin engine, and I would never worry about lack of air again.

Think yer talking about a inline sander ? Great for body work,just takes a little practice to learn how to use it. Sanding bondo,just use a X pattern to get it close to flat. They do use a lot of air. Big time saver !
I always had Viking brand inlines. They lasted a very long time !

 

[Stihl 041S]

Yep I is delicate

Hey Rob!

Wouldn't be so bad if it didn't take ten pulls when cold to start

The heat just makin everyone miserable including the puppies

The stupid cat likes it tho

Stuupd kat!!!!!

Some of my saws take a prime one fire a LOT quicker.

North of 100 ccs I just do it if it has been sitting.

 

[tbone75]

I'm sure it is

180psi no decomp and a bear to start!

Sure runs tho!

You should try my 480 , 200 psi no decomp. LOL

Wimp ! I can even start it !

Not sure what the MM 064 has ? May check it just for fun. LOL Should be broke in good by now. LOL
Got a 20" bar on the MM064 right now,talk about fun !!

 

[tbone75]

Stuupd kat!!!!!

Some of my saws take a prime one fire a LOT quicker.

North of 100 ccs I just do it if it has been sitting.

Stupid cat ? How many ya want ? :msp_rolleyes:

 

[tbone75]

Adam give the L side another 1/8 -1/4 out. Usually helps starting cold ?

 

[IEL]

Think yer talking about a inline sander ? Great for body work,just takes a little practice to learn how to use it. Sanding bondo,just use a X pattern to get it close to flat. They do use a lot of air. Big time saver !
I always had Viking brand inlines. They lasted a very long time !

Thats the kind. Hutchins website said only 6 cfm needed. National detroit said 11 cfm. I think my compressor does 11 cfm. It should just run it. Once I get my devillbiss going, and can hook them together for 15-16 cfm.

Any thoughts on the 8" gear drive sanders? (bondo buster, bondo hog, mug hog, ect)
Look good for paint stripping?

 

[Stihl 041S]

Stupid cat ? How many ya want ? :msp_rolleyes:

I like Katz. If they are on the loopy side. Mousers be Kool.

 

[Stihl 041S]

Adam give the L side another 1/8 -1/4 out. Usually helps starting cold ?

That may become a tattoo!!!!

 

[IEL]

You should try my 480 , 200 psi no decomp. LOL

Wimp ! I can even start it !

Not sure what the MM 064 has ? May check it just for fun. LOL Should be broke in good by now. LOL
Got a 20" bar on the MM064 right now,talk about fun !!

What size sprocket are you running? I bet a 10 pin on that would be really fun.

 

[tbone75]

Thats the kind. Hutchins website said only 6 cfm needed. National detroit said 11 cfm. I think my compressor does 11 cfm. It should just run it. Once I get my devillbiss going, and can hook them together for 15-16 cfm.

Any thoughts on the 8" gear drive sanders? (bondo buster, bondo hog, mug hog, ect)
Look good for paint stripping?

Never had a gear drive ? Can't member what that file is called I used to shape it with ? Just used that to knock off the high spots,then the inline.
Just have to file it before it gets real hard. Surform file maybe ?

 

[tbone75]

I like Katz. If they are on the loopy side. Mousers be Kool.

All my cats are loopy ! LOL What makes them fun to watch ! LOL

 

[tbone75]

What size sprocket are you running? I bet a 10 pin on that would be really fun.

7 I think ? Could be 8 ?

 

[tbone75]

That may become a tattoo!!!!

You need some more sleep, yer loopy ! :hmm3grin2orange:

 

[Stihl 041S]

You need some more sleep, yer loopy ! :hmm3grin2orange:

I'm telling MOM!!!!!!

But I think she agrees with ya........

 

[tbone75]

Just got another chuck in the back yard ! First one back there this year. Mom seen it out the window. LOL

 

[tbone75]

I'm telling MOM!!!!!!

But I think she agrees with ya........

I know she does ! :msp_w00t:

 

[IEL]

A fan makes this weather much more survivable. Still too hot....

 

[farrell]

My fans ain't cuttin it!

Still dripping with sweat

This blowes!