Swap meet...

[Mastermind]

According to my IPLs, that linkage will work on a 250. Good luck!

Your clutch cover left here today.......I'm always a bit slow to ship stuff.

 

[ChainsawmanXX]

The following error occurred during processing

ChainsawmanXX has exceeded their stored private messages quota and cannot accept further messages until they clear some space.

ARRGGGG!! You made me work!
Its clean now.

He always comes up a little short. :msp_w00t:

Watch out there Mr King :msp_angry:

 

[bushwackr]

Anyone looking to trade a saw I have a 028 super w/ brake runs great . Im looking to get a 026/260 for my better half. looking to trade powerhead only

 

[axlr8]

Bump!!! Anyone have ANY clue where to source these parts at??? (Stihlership will be the LAST resort!)


okay guys, i am going to see what you guys got going here.... I need:

2 sets of Stihl 056 bearings.... Would love NOS!

same with seals!

a Few (5 ish) Stihl Name plates, as you have riveted on the side of a recoil (NOS is great! and Id like if they said "made in west Germany"!

Some metric rivets for the Above item would help also!

And also looking for used P/C kits for the 056 super, and 056 magnum 2 varieties! I need one of each :/

 

[o8f150]

i don't have the saw yet but does anyone have the recoil assembly for an olympic 355af ??? if i can find the parts i am going to buy the saw for 10.00,, have useless green paper and some parts for trade

 

[o8f150]

He always comes up a little short. :msp_w00t:

from what i hear thats what his wife says too :msp_biggrin::msp_biggrin:

 

[ChainsawmanXX]

from what i hear thats what his wife says too :msp_biggrin::msp_biggrin:

I found out the hard way yours likes the whips an chains!! :0

 

[tbone75]

I found out the hard way yours likes the whips an chains!! :0

How else can his wife keep him in line? :hmm3grin2orange:

 

[Scooterbum]

Have what appears to be the Monkey Wards 2.1 cu. in. version of the McCULLOCH MacCat-WildCat type saw.

I'm looking for a clutch and sprocket assembly for it. Have green stuff to trade.

 

[thomas1]

Have what appears to be the Monkey Wards 2.1 cu. in. version of the McCULLOCH MacCat-WildCat type saw.

I'm looking for a clutch and sprocket assembly for it. Have green stuff to trade.

Scoot, can you poat a pic? I've got a few carcasses, here.

 

[bplust]

Bump!!! Anyone have ANY clue where to source these parts at??? (Stihlership will be the LAST resort!)


okay guys, i am going to see what you guys got going here.... I need:

2 sets of Stihl 056 bearings.... Would love NOS!

same with seals!

a Few (5 ish) Stihl Name plates, as you have riveted on the side of a recoil (NOS is great! and Id like if they said "made in west Germany"!

Some metric rivets for the Above item would help also!

And also looking for used P/C kits for the 056 super, and 056 magnum 2 varieties! I need one of each :/

Would seals/bearings from a plain old, as in not "Magnum", 045/056 work? I might have them, I have a bunch of NOS stuff, but I don't know the how the bearing and seal part numbers work, so I haven't gotten around to sorting them out. If you can provide me with part numbers, I'll see if I have what you're looking for.

Bryan

 

[Scooterbum]

Bump!!! Anyone have ANY clue where to source these parts at??? (Stihlership will be the LAST resort!)


okay guys, i am going to see what you guys got going here.... I need:

2 sets of Stihl 056 bearings.... Would love NOS!

same with seals!

a Few (5 ish) Stihl Name plates, as you have riveted on the side of a recoil (NOS is great! and Id like if they said "made in west Germany"!

Some metric rivets for the Above item would help also!

And also looking for used P/C kits for the 056 super, and 056 magnum 2 varieties! I need one of each :/

Have 056 magII and super cylinders, no pistons though.

 

[Scooterbum]

Scoot, can you poat a pic? I've got a few carcasses, here.

Sent via text to your phone. It's a TMY240 model. Also need the little plastic plate that covers the carb.

 

[Jacob J.]

Have 056 magII and super cylinders, no pistons though.

The pistons are the hard part to come up with for the Magnums/Magnum IIs.

 

[Scooterbum]

The pistons are the hard part to come up with for the Magnums/Magnum IIs.

No aftermarket ? I'll have to do some digging then, I'm sure I have some used ones here.

 

[Jacob J.]

No aftermarket ? I'll have to do some digging then, I'm sure I have some used ones here.

There are some Chinese pistons being made but the reviews so far are not good. Even good used OEM would be better, and if they're worn past
specs, then a guy could have Millennium Technologies coat the piston to bring it back.

 

[parrisw]

There are some Chinese pistons being made but the reviews so far are not good. Even good used OEM would be better, and if they're worn past
specs, then a guy could have Millennium Technologies coat the piston to bring it back.

If there was enough of you guys interested, you could doo what Lee did for the 166's and have a bunch made.

 

[Metals406]

If there was enough of you guys interested, you could doo what Lee did for the 166's and have a bunch made.

And the 056 pistons work well in 066's! :msp_biggrin:

 

[Mastermind]

And the 056 pistons work well in 066's! :msp_biggrin:

If this ends up going somewhere I would be in for a few....

 

[Jacob J.]

And the 056 pistons work well in 066's! :msp_biggrin:

I've built three 066s for saw millers using the 056 Super piston, it does make a good running machine.

It's not a high-winder, but they make good torque.