mowoodchopper
Polar Bear
looking for a good 385/390 dosent need to be pretty
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
fastLeo151
Addicted to ArboristSite
looking for the bushing/ sleeve that goes between the worm gear and the crank on my 034. I had an air leak on the pto side oil seal and had to cut that sleeve off. heres the part number
0000-993-0510
0000-993-0510
homelite028
ArboristSite Operative
two p50 pioneers
I have two nice strong running pionners not been used alot 24inch bars great compression one has full warp .need to sell .need bill money
606-878-6285 ben
270$$ for both its a good deal
I have two nice strong running pionners not been used alot 24inch bars great compression one has full warp .need to sell .need bill money
606-878-6285 ben
270$$ for both its a good deal
Last edited:
homelite028
ArboristSite Operative
p50 pioneer cylinder and piston other parts
i have a piston and cylinder in great shape not been used alot for the p50 pionner..
i have extra parts laying around for the p50 to p60 pioneers
606-878-6285 ben i need to sell
i have a piston and cylinder in great shape not been used alot for the p50 pionner..
i have extra parts laying around for the p50 to p60 pioneers
606-878-6285 ben i need to sell
Anyone have a MS362 with a bad top end that they would be willing to part with? I have a saw in a box project and I am looking to rebuild it. I have some stihl chains, a couple pieces of crumpled cotton with ink stains and a few saws for trading material.
Last edited:
350jeepcj5
ArboristSite Operative
Anyone have a MS362 with a bad top end that they would be willing to trade on? I have a saw in a box project. I have some stihl chains, a couple pieces of crumpled cotton with ink stains and a few saws for trading material.
You didn't tell me you had that wen I was up there, I would have been happy to take it off your hands
But it just came in the box today. I would like to build it to fit between the 064 and 200 if possible.
350jeepcj5
ArboristSite Operative
Nice, good luck with it!
Mastermind
Work Saw Specialist
I only have the complete cover with older stihl logo from a 08S parts saw.
It won't work......
The older 08S has a different starter setup. The recoils with the rectangular tag have pawls and those old logo types have cups in the flywheel.....
o8f150
Tree Freak
i will give you 2.80 for both :msp_rolleyes::msp_rolleyes: just kidding
how you been ben
homelite028
ArboristSite Operative
Been doing good trying to stay busy.. been working my butt off on the farm
the two p50 pioneers i lowerd the price 270$$ for both
theses are strong running 82cc saw starts on the 3 pull ..pulls the 24inch bar fine
the two p50 pioneers i lowerd the price 270$$ for both
theses are strong running 82cc saw starts on the 3 pull ..pulls the 24inch bar fine
Last edited:
AU_K2500
NSM
Good to know. Thanks Randy!
Nogoingback
ArboristSite Operative
:help:
SawGarage
Addicted to ArboristSite
BUMP
I'm also needing a Husky 435/440 carb. I picked up a saw that was worked on by a Gorilla last
They RUINED the needle seats,and adjusting the needles becomes almost USELESS....
--a filter for a
oh, and a 066 brake lever/handle in decent condition..
I have a couple new elasto-start ropes/handles/ etc I'd trade..as well as some rounded-off bar nuts
I'm in desperate need of (I know it's NOT saw related, BUT, it is a Stihl :msp_sad: )
an FS-45 ignition coil...
I have stuff to trade for it
I'm also needing a Husky 435/440 carb. I picked up a saw that was worked on by a Gorilla last
They RUINED the needle seats,and adjusting the needles becomes almost USELESS....--a filter for a
oh, and a 066 brake lever/handle in decent condition..
I have a couple new elasto-start ropes/handles/ etc I'd trade..as well as some rounded-off bar nuts
Last edited:
srcarr52
We can't stop here, this is bat country.
Baileys has the majority of the piston measurements in their part descriptions that you'll need for researching piston swap ideas. The only thing they don't give is skirt width, of which a 317/372 piston is a full skirt piston so it doesn't matter.
Mastermind
Work Saw Specialist
In the mail Ed. :msp_wink:
Anyone have use of any of the following... I posted them on the "other swap meet" but evidently they are "usefull items"... LOL
Coleman Powermate 2500w generator - Verticle shaft engine type and runs great! Grandfather bought in 1999 b/c of the 2000 scare run maybe 3-6hrs
Honda 1000i Generator not sure what owner wants from it. Retired minister of ours that had it at a cabin in CO. Super quiet he says...
Honda WX10 Water Pump
Make any reasonable offer via PM if you're interested in any of the above...
Coleman Powermate 2500w generator - Verticle shaft engine type and runs great! Grandfather bought in 1999 b/c of the 2000 scare run maybe 3-6hrs
Honda 1000i Generator not sure what owner wants from it. Retired minister of ours that had it at a cabin in CO. Super quiet he says...
Honda WX10 Water Pump
Make any reasonable offer via PM if you're interested in any of the above...
ChainsawmanXX
Addicted to ArboristSite
Looking for rings for a 1020 homelite.
Also Anyone have any plastic wedges laying around? They dont have to be brand new.
Also Anyone have any plastic wedges laying around? They dont have to be brand new.
