Swap meet...

[o8f150]

Doing another unibearing conversion?

now that is funny,,
did you get that bar yet tim??? i tried to send the number but your pm box was full last week

 

[Freakingstang]

I've also got a really nice husky 154xp cylinder, no piston...

 

[RedneckChainsawRepair]

I have an echo 670 clutch cover, no brake guts or handle, but the cover is in great shape. Would that work for you?

I have your 2100 switch in hand now. Thanks.

 

[Gologit]

I have a 3/4 wrap handlebar for a 660 Stihl. I'll take 114dl, 84dl, or 72dl chains in trade. PM me.

Gone. Thanks to all who replied.

 

[dh1984]

Doing another unibearing conversion?

Nope just like to have setting around the shop looking pretty LOL.

 

[tmessenger]

I'm about 80% sure I have one for you!


Looking for 026 carbs... I don't need 194 or 22's... I'll take the fixed "H" jet carbs b/c I'm just making a couple saws to sell...

I have one of these for the cost of shipping.

Tim

 

[parrisw]

I have a 084 piston and cylinder. it came off of a low hour saw...

I have a 385 cylinder with low use (not scored or honed) but a small section of the second fin is broken off

I have an 036 pro cylinder that is in like new shape, also a meteor piston for it.

I have a couple 371/372 topends, i'm looking for a 375/372xpw topend.

I'm always looking for 385-372 stuff, anything you're in need of?

 

[leecopland]

Hi Guys,
After a recent Poulan rebuild one of the wrist pin clips came loose and screwed my cylinder. I think most 40cc poulan/craftsman cylinders will fit.

Thanks for looking, I have a later Poulan cylinder to trade in excellent condition. The one that uses the strato carb I think it is a 42cc.

Regards,

Lee
:msp_unsure:

Still in need!

 

[o8f150]

Still in need!

let me check lee,, i think i have what you need,, i have several parts saws in the shop,,,

 

[fastLeo151]

any one gots a nice 046 tank laying around? I haves loads of junk to swap or some mooney to trade.:msp_tongue:

 

[leecopland]

let me check lee,, i think i have what you need,, i have several parts saws in the shop,,,

Thanks for taking the time to look. Hear from you at your convenience.

Regards,

Lee

 

[o8f150]

Thanks for taking the time to look. Hear from you at your convenience.

Regards,

Lee

i went out to take a fast look a while ago and didn't see one,,, i know i have one someplace since i have 2 of those saws torn down in the box due to a smoke piston,, i will do some major digging in the morn for you

 

[nstueve]

where did neil go... I found a 036 oil pump but need his addy to mail it out!

 

[ELECT6845]

POULAN 3400's and Homelite 360's

Anyone looking? I have (4) 360 homelites all complete and run with some mix in the carb. The one Poulan 3400 has all the original paperwork and receipt. The other poulans are complete and clean but need work. Looking for Husqvarna project.

 

[bigbadbob]

Looking for a good used Makita/Dolmar DCS401 P&C
BBB

 

[axlr8]

Looking for a good used 044 tank for another member. Anyone have one laying around???

 

[Whiskers]

Looking for a Regular Stihl mount bar for an 036.

16" 3/8 .063 - Let me know what you've got, I've got parts and cash.

 

[Stihl 041S]

let me check lee,, i think i have what you need,, i have several parts saws in the shop,,,

Looking for a Regular Stihl mount bar for an 036.

16" 3/8 .063 - Let me know what you've got, I've got parts and cash.

I might have a new 18" but no 16".

Stihl wrap handles are good

 

[Whiskers]

I might have a new 18" but no 16".

Thanks, I'll keep the 18" in mind.

 

[Trx250r180]

Looking for a good used 044 tank for another member. Anyone have one laying around???

i have one that has had a repair on the handle end ,i can get a pic tonight see if useable enough ,its still pretty white ,not all browned like most of them get