Swap meet...

[Jacob J.]

Out of curiosity, what's the number on it? The one I have is a 48MM with the following numbers:

V 2H.
+ A4
50ZK6 W1

Be nice to have the rest of the saw to go with it if someone happens to have all the remaining parts just layin' around in a box somewhere.:msp_biggrin:

Looks like you have a Husky 365 cylinder there. I have one in front of me with identical markings.

 

[Jacob J.]

anyone have some 404 80 gauge chain have cash to trade thanks BILL

How much do you need?

 

[PogoInTheWoods]

Looks like you have a Husky 365 cylinder there. I have one in front of me with identical markings.

Thanks for the clarification. Appreciated.

So does anyone else have the rest of the saw they'd like to trade for a coupla boxes full of 1127 stuff?

 

[Overtrained]

Round and round the little Mac goes where it stops nobody knowss

 

[turbo885]

How much do you need?

dont matter anything from pieces to a roll. using 85 drive link loops thanks BILL

 

[struggle]

Pipe it

 

[Jacob J.]

dont matter anything from pieces to a roll. using 85 drive link loops thanks BILL

Bill- I can get you a couple of loops. A logging company I used to work for runs .404 x .080" on two of their feller-bunchers
and they give me old stuff all the time including chains and bars. It's lucky I did good work for them.

 

[turbo885]

Bill- I can get you a couple of loops. A logging company I used to work for runs .404 x .080" on two of their feller-bunchers
and they give me old stuff all the time including chains and bars. It's lucky I did good work for them.

Thanks that would help i just cant swing a roll right now BILL

 

[Martijn]

Flywheel for echo 330 evl

Hello trying to get a flywheel for echo 330evl , looked on eBay and too expansive.
Could swap mini Mac parts or poulan parts for the flywheel.
Let me now and we will make it work!(again):msp_biggrin:

 

[homelite028]

need a stihl 044 or ms440 handle

i need the rear handle and gas tank assembly there built in together for my 044 stihl fixing it up for my dad
i have green or pioneer p50 p60 p51 parts to trade

 

[fastLeo151]

G

I think they are different, and I dont have the part number. Ill see what I can come up with.

1

I know I have one but I have a about 3 regular 041 flywheels in the same crate :msp_confused:

 

[Arrowhead]

i need the handle and gas tank assembly for my 044 stihl fixing it up for my dad
i have green or pioneer p50 p60 p51 parts to trade

Ben, what kinda Pioneer parts do you have?

 

[DSS]

Ben, what kinda Pioneer parts do you have?

Bastard. I think my internets frozed.

 

[cbfarmall]

Anybody have a good full wrap handle (with those little spacers) for a Jonsey 670? They seem to be few and far between.

Chris B.

 

[bplust]

Speaking of full wraps, does anyone know if one was made for the 10-series Macs? I have a pm700 and a 7-10a that I'd like to put one on, please PM me if you have one.

I'm also on the hunt for an 80cc Mac (sp81, pm 800/850) saw or project saw (nothing that needs a new top end, as I probably won't find that).

Lots to trade or $$$.

Bryan

 

[Warped5]

Speaking of full wraps, does anyone know if one was made for the 10-series Macs? I have a pm700 and a 7-10a that I'd like to put one on, please PM me if you have one.

I'm also on the hunt for an 80cc Mac (sp81, pm 800/850) saw or project saw (nothing that needs a new top end, as I probably won't find that).

Lots to trade or $$$.

Bryan

I did see in a eBay auction recently where the seller installed a full-wrap on a 10-10A. They referred to it as an uncommon accessory, which led me to believe it was different than the two offered for the SP70/80/81. Maybe send a PM to Mark H and he can clarify for you.

The 80cc Macs are a hot commodity around here right now. There's an SP81 runner and an SP80 project on eBay right now.

 

[paccity]

I'm also on the hunt for an 80cc Mac (sp81, pm 800/850) saw or project saw (nothing that needs a new top end, as I probably won't find that).

Lots to trade or $$$.

Bryan

how bad do you want one.

 

[Toad22t]

I am looking for a 044 or 046 parts saw. I would prefer it to be complete itch a good bottom end to it. In the perfect circumstance would be a 12mm 044 with a burnt up p/c. I'm wanting to build a 044/046 hybrid. I already have a good 046 cylinder waiting on my bench. Lol

I am also looking for a 85 cc or bigger project saw with a decent part availability for it. Once done with it I would like to be able to put a 36 inch bar on it for big hard wood.thank you for any help that could be offered. Toad22t

Ok I'll try this again! Have cash and possibly some parts/ part saws.

 

[bplust]

how bad do you want one.

Not that bad. I'd love to have one, as I'm very happy with my 7-10a's and pm700's, and have heard great things about their 80cc family members, and am willing to trade for them, but won't pay much for them. The lack of parts availability is a concern to me. I just heat with wood and take down occasional problem trees, it's not like I'm a production cutter, so I don't really NEED to own anything too nice. Plus I live in Northeast Vermont, so the wood doesn't get too big around here. But I bet they are fun!

So I guess I don't want them too bad. But would like one (or more), so if you or someone else are open to at least partial trading or have one that's a project, let me know.

 

[Axlerod74]

Jonsered 2050 turbo

Looking for a chain catcher and a starter decal. What do YOU need?