Swap meet...

[bigbadbob]

View attachment 276464

Not chainsaw but,,,,does any one have a dead old craftsman pressure washer???
I need one valve and you cannot buy it alone.
Sears want $240 for a kit, not worth it!!
Model is 919-672240
Its from a vertical model and the pump is under a cover because it has exposed moving parts.
A entry level machine probably quite common, honda GCV160 5.5hp.
About 10 years old.
BBB

 

[lumberjackchef]

Looking for any of these items:

Husqvarna 50/51/55 top end
Crank to fit a 3.7 craftsman/ 3700 poulan
Set of thin rings, air filter and filter cover for a Johnny 920


Got lots of saw stuff for trading just let me know what ya need between me and my buddy we got like 350+ parts saws of every color!

Or there's always those greenbacks......

 

[Eccentric]

If it doesn't get thrown in that box let me know what you'd like for it.

Looks like Ted needs it. I may have another spare spike. When I'm in the shop I'll see if I can scare one up for you. Probably won't have 'correct' screws/nuts for it (this unfortunately goes for yours too Ted). Most of my parts saws have 'improvised' fasteners holding the spikes on. If I don't get back to you by next week please PM me. My memory isn't the best and family/work keeps me quite busy...

Looking for any of these items:

Husqvarna 50/51/55 top end
Crank to fit a 3.7 craftsman/ 3700 poulan
Set of thin rings, air filter and filter cover for a Johnny 920


Got lots of saw stuff for trading just let me know what ya need between me and my buddy we got like 350+ parts saws of every color!

Or there's always those greenbacks......

I believe I have a good crank/conrod for you. These next couple weekends are going to be BUSY for me, so I don't know if I'll be able to pull them and ship for a few weeks. Will TRY to get those cases split (along with everything else I'm doing) tomorrow and Saturday. Gotta work Sunday through next Thursday, and that next weekend I'll be busy all the way through. After that, things get back to 'normal'. I'm sure we can work out a trade deal for the crank/conrod. Like I said above..............if I don't get back to you by next week go ahead and PM a reminder to me.....

 

[Jimmy in NC]

If I don't get back to you by next week please PM me. My memory isn't the best and family/work keeps me quite busy...

No worries. I'll know by then if the parts saw that is headed my way has one on it or not. Didn't even think about that earlier! I know all to well about being beyond busy!

 

[chainsawwhisperer]

Looks like Ted needs it. I may have another spare spike. When I'm in the shop I'll see if I can scare one up for you. Probably won't have 'correct' screws/nuts for it (this unfortunately goes for yours too Ted). Most of my parts saws have 'improvised' fasteners holding the spikes on. If I don't get back to you by next week please PM me. My memory isn't the best and family/work keeps me quite busy...



I believe I have a good crank/conrod for you. These next couple weekends are going to be BUSY for me, so I don't know if I'll be able to pull them and ship for a few weeks. Will TRY to get those cases split (along with everything else I'm doing) tomorrow and Saturday. Gotta work Sunday through next Thursday, and that next weekend I'll be busy all the way through. After that, things get back to 'normal'. I'm sure we can work out a trade deal for the crank/conrod. Like I said above..............if I don't get back to you by next week go ahead and PM a reminder to me.....

If your gonna be splitting cases, I could use a Right side case 1/2 for a 3400-4000.
j

 

[tomdcoker]

Looking for any of these items:

Husqvarna 50/51/55 top end
Crank to fit a 3.7 craftsman/ 3700 poulan
Set of thin rings, air filter and filter cover for a Johnny 920


Got lots of saw stuff for trading just let me know what ya need between me and my buddy we got like 350+ parts saws of every color!

Or there's always those greenbacks......

Do you have a good gas tank for a McCulloch 850 or 895. If you do PM me with what you want for them.. Thanks Tom

 

[excess650]

Stihl BT 45

not a chainsaw, but does anyone have a gearbox, or at least the output shaft for a Stihl BT 45? Some maroon must have thrown it down and snapped the end off the shaft.

 

[struggle]

Looking for parts for my school's FS 85 trimmer. Needing a
recoil, muffler, and possibly the handle fer the trigger and ign switch

Will this work. Three bolt. No rope but the inner part is there and appears to wind up proper

 

[SugCutter]

i might actually have a spare... I'll have to check and see if it cleans up first...

:msp_biggrin:

LMK,
I have the saw torn down to the cases and I'm itchin to put it back together.
Sug

 

[jbird77]

got some goodies

I have a friend who brought me some goodies yesterday , he brought me a ts 350cut off and two ts 400,s and one makita 7301 cut off , i was wonderin if any one had a muffler for one of the ts 400,s

 

[psuiewalsh]

:too_sad:

Are you still looking for one of these?

 

[Warped5]

Are you still looking for one of these?

I have it covered now.
But thank you for asking!

 

[lumberjackchef]

anybody got an old partner k950 with a good crank in it. I rebuilt one from bearings up and overlooked that the wrist pin bearing hole was out of tolerance. So now all I need is a different crank and I'll have a solid machine again.

 

[Jacob J.]

anybody got an old partner k950 with a good crank in it. I rebuilt one from bearings up and overlooked that the wrist pin bearing hole was out of tolerance. So now all I need is a different crank and I'll have a solid machine again.

The small end of your connecting rod got wallowed out? I'd be interested in seeing that. I've never heard of that before. I'm assuming you already tried a new wrist pin and wrist pin bearing.

 

[lumberjackchef]

Yeah I thought that was strange myself. Its a brand new p/c and bearing but the play is definitely in the wrist pin piston hole. never seen it before either that's why I thought it was a little weird. Oh bearing is oem p/c is aftermarket(stens).

 

[Jacob J.]

Yeah I thought that was strange myself. Its a brand new p/c and bearing but the play is definitely in the wrist pin piston hole. never seen it before either that's why I thought it was a little weird. Oh bearing is oem p/c is aftermarket(stens).

Any visible signs of wear in the connecting rod? Those things ingest a lot of concrete dust so that kind of wear and tear wouldn't be abnormal. I've just never seen it in a chainsaw.

 

[lumberjackchef]

Far as I could tell It was solid, no vertical play, very, very little horizontal movement. I've had 66's that the rod bearings went south on and i could move them vertical and about 3/16" side to side but never saw them wear in the wrist pin area. Possibly could've been the dust cause thats what finally killed it! She had probably been eating it for a while.

 

[barneyrb]

I am putting some feelers out here, got a guy looking for a Echo CS-510evl or JDeere Cs equal. He loves that saw design and size but his was "borrowed" from the bed of his truck. If it needs a little repair that is all the better, must have a usable cylinder assembly. I have some cash, dolmar parts, husky parts, and some JRed parts.

 

[MechanicMatt]

Ed, Arrowhead, If you still need that 42cc topend I might have one kicking around. Do you happen to know if you have the Husky small mount in 3/8th by 20in? 050 works but ill take 058. Thanks.

I also need the throttle linkage for a 357xp and the rubber grommet piece that it slides through, if none found by the weekend Ill buy one from Spike60. I gotta love that guys store, got three husky's running since sunday from the goods he sold me. 372, 266, 346 all back to throwing chips. Wish I had remembered the 357's parts while I was up his way.

 

[axlr8]

Might have some of that.

I need the recoil handle, muffler, air filter, possibly some other parts..