Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
Mastermind
Work Saw Specialist
I'm planning on building that saw for him.....if we can find a top end. :msp_wink:
Mastermind
Work Saw Specialist
On an unrelated note.......I'd like to trade a really nice Poulan WildThing for a Mall two man saw. I'd gladly pay the shipping on the Poulan.......but only if the Mall is in perfect condition.
Jimmy in NC
Addicted to ArboristSite
M
moody
Guest
You're at least going to need to throw the stock 28inch bar and chain in to get the mall.
Who was it that asked me about Super EZ bars? I still got quite a few.
440 tank is a done deal elsewhere, 2nd inline took it. 044 tank is done too just pending closure. You are next inline on 044 IF, then jj.
440 tank is a done deal elsewhere, 2nd inline took it. 044 tank is done too just pending closure. You are next inline on 044 IF, then jj.
Thanks !!
I think you were saving me a 16" and a longer one also.
Right, your one of them! I got a near mint 16" hardnose for you and a not so mint 24" for you, I'll put em aside tonight.
Eccentric
Mister Wizard
Mark we talked about a 16" and a 24" hardnose bar for the E-Z/XL-101 series saws too. If there are any left to put aside for me I'd appreciate it of you could put my name on one of each. No big deal if not however...
No problem, I'll see what I can do but I think theres only the one 24" left and Eds got dibbs. You want a 20"? I might have some of those.
SawGarage
Addicted to ArboristSite
I've built the saw ( Husky 394) for Jay.... I bought a crusty carb from another member that was supposed to be good, but was worn to all sin (throttle shaft bore leaked as bad as a mis-placed intake gasket! :bang: SO... I pirated my own carb for the build, and am needing a replacement... The shafts I have are good, so JUST a carb body would work, unless someone has a WJ-39, or 70 or??
for the 394...
Maybe this would warrant an offer to a member with a REALLY CLEAN saw, but I have a NOS 056 mag cyl
JJ- We need to get back on the same page with our last deal
... I think we both have too much to offer to AS and each other to be at a stale-mate. give a shout in the evening when you have time... i'm usually up till 9-10pm your time...
J
Eccentric
Mister Wizard
Warped5
WingNut
A 20" would be fine Mark. I want to see Ed put that 24" bar on somethin' cool.
He WAS working on a 1050 .... but that bar would be a bit undersized ....
Mastermind
Work Saw Specialist
Maybe this would warrant an offer to a member with a REALLY CLEAN saw, but I have a NOS 056 mag cyl
I can't understand your lingo too well Jay......but I'm sure we'll find one somewhere.
SawGarage
Addicted to ArboristSite
:msp_w00t: With that being said....
The shop could use:
Husky:
435-440 carb someone crushed the L-speed needle... runs rich all the way in :bang:
445-450 coil - has no advance? odd...
257-262 inner bar plate
272 top cover
394/5 coil, intake boot & muffler
Stihl:
044 & 046 tanks
044 carb
I have 12,602.7 parts, 523.3ft of chain, and 139 l/ft of bars to trade
The shop could use:
Husky:
435-440 carb someone crushed the L-speed needle... runs rich all the way in :bang:
445-450 coil - has no advance? odd...
257-262 inner bar plate
272 top cover
394/5 coil, intake boot & muffler
Stihl:
044 & 046 tanks
044 carb
I have 12,602.7 parts, 523.3ft of chain, and 139 l/ft of bars to trade
SawGarage
Addicted to ArboristSite
Randy,
It's the beer talking
LOL!!I guess it means, if the saw is worth (to the owner) a new cyl, I have one. Example: I've offered NEW parts to members before, and the reply I've got more than once was 'the saw isn't perfect, I don't need new'...
What ever that means
How's things Randy?
