Swap meet...

[Duke Thieroff]

Thanks for the reply. I already got hooked up, but I think I'll try one at some point. Been curious about those.

Bump for Bryan, the one I had was a little rough.

 

[cat-face timber]

Looking for a Chainsaw buddy,

I have a Husky 136/142 missing Carb PHO for trade.
Or....
This sure looks like it would come in handy.

 

[mitch95100]

Looking for a Chainsaw buddy,

I have a Husky 136/142 missing Carb PHO for trade.
Or....
This sure looks like it would come in handy.

I'll be your buddy


Sent from my iPhone using Tapatalk

 

[cat-face timber]

Almost what I meant Mitch...
You do drink coffee and use snuff right

 

[7hpjim]

Almost what I meant Mitch...
You do drink coffee and use snuff right

me too, coffee yes, gave up rubbin

 

[tbone75]

Anyone have a 346,353,351 crankcase they would let go of ? Gotta be the all mag case. Gots stuff to trade !
No luck on a 346xp clutch side half yet.

 

[Flat47]

Looking for a gas tank and handle bar for Husky 372. The cheaper the better. Have misc extra 372 parts to trade (cranks, oil pumps, clutch, etc) and a Husky 266/JRed 630 two piece ignition. Maybe a long shot there...

Bump...I'll add cash (if I have any at the moment) and my standard offer of maple syrup, too. Anybody???

...still looking...

 

[mp5n]

Looking for an air filter for a Stihl 015L. If anyone can help out please PM.

Thanks in advance,
MP5N

 

[mitch95100]

Almost what I meant Mitch...
You do drink coffee and use snuff right

Coffee yes, wouldn't make it without it. Snuff no but hey more for you.


Sent from my iPhone using Tapatalk

 

[nstueve]

Ok so I'm circled back around to a nice running 015 Stihl that is currently 1/4 pitch and the owner would like to put on 3/8 LP if possible. Anyone got a parts saw with 3/8 setup???

 

[Wagnerwerks]

I still have the clutch drum if you need it. No oiler gears...

 

[nstueve]

I still have the clutch drum if you need it. No oiler gears...

Cool... I'll see if I can get it tore apart tomorrow so I can see what I need. I think there is a plastic plate or oiler gear right under the drum from just looking at it. Seems like the spur count has to be the same as that part. Will take pics tomorrow.

 

[Wagnerwerks]

Yeah... You need 2 more pieces but the inner one might be the same... I have a 1/4" set yet, but no more 3/8 drum gears.

 

[rocketnorton]

...Good paint and its steel. Not sure if its aluminum or mag but its good quality.

????

 

[Duke Thieroff]

Put this on the trading post also, just looking to expand the base of folks of which I pull from.

Looking for a decent chain grinder, 511A or AX, even an NT one. Brands don't matter (except HFT). Any upright grinder considered.

Trades a million / cash / store credit available.

 

[tlandrum]

Looking for a gas tank and handle bar for Husky 372. The cheaper the better. Have misc extra 372 parts to trade (cranks, oil pumps, clutch, etc) and a Husky 266/JRed 630 two piece ignition. Maybe a long shot there...

...still looking...

I think I have a used tank and new aftermarket top handle. I need a good set of 372 cases. id trade the tank for cases and the handle bar is $35

 

[Wagnerwerks]

Terry, I have a beat up case at home that I need to split to see what's what. Might have a good bar side. I'll check for you if you need it. It free for you if it's good.

 

[tlandrum]

I can remember what side this saw needs. I split it to replace a bad bearing and the bearing on one side just falls out of the case.

 

[sefh3]

Anyone have a Tilley HU carb laying around? The fuel inlet on mine is cracked an sucking in air.

 

[sefh3]

Anyone have a Tilley HU carb laying around? The fuel inlet on mine is cracked an sucking in air.