Swap meet...

[Steve NW WI]

I need a 14-16" 3/8 low pro bar for a Homelite XL2

I have a .325 16" bar for the same to trade or some worthless dollars.

Is this what ya need:

EDIT: It's 16", .050, .375LP

The rails look fairly good, with some wear at the saw end. The sprocket has a little play in the bearings, but it should be very useable, especially with some grease in there, it's dang dry right now.

PM me if you want it, I'm sure not using it any time soon.

I could use some Power Mac 6 parts right now if ya have any, if not we can work something out.

For anyone else reading this wondering what I'm looking for for the PM6, here is the list:

Parts needed for PowerMac6

choke knob 68659

muff cover 69160
clip locking 68725
baffle 68669
or if you have the full muffler assembly, all I have is the base right now.
full muff assy:
kit spark arr 68768

fuel barb 67581 - not sure I need this, but it doesn't seem to seal tight to the tank. Maybe I'm just not doing something right?

 

[roncoinc]

Randy,looks like you got better choices than what i have to offer.
my bars need cleaning and work but those where the ones i could find in 10 seconds,may have more.
think going to keep the red one.
acid,sand and paint make any look fine.

 

[sefh3]

Anyone have a case for a Stihl 025 laying around? I picked one up but the clutch toasted the outside of the case. I have parts and $$.

 

[thomas1]

Anyone have a case for a Stihl 025 laying around? I picked one up but the clutch toasted the outside of the case. I have parts and $$.

I have a couple of 025 parts saws I could part with. I need to get a list of my 041 needs together.

 

[blackoak]

I need a 14-16" 3/8 low pro bar for a Homelite XL2

I have a .325 16" bar for the same to trade or some worthless dollars.

How many do you want? I have several brand new 14" or 16" GB bars for the little Homelites that use the square hole mount pattern?

 

[blackoak]

Echo 510 EVL

I have a very mint Echo 510 EVL that has no spark. I need either the coil or the ignition module for this saw.If you have both that will be great. I have a barn full of parts saws for parts to trade or I have cash.

 

[MiracleRepair]

Anyone have a case for a Stihl 025 laying around? I picked one up but the clutch toasted the outside of the case. I have parts and $$.

If Thomas can't help you out I've got one I just picked up.



Roanoaker, what you want for the good 55 top end?

 

[little possum]

Shop clean out:
Poulan 71A- was a runner, paint loss, was Virginia DOT orange at one point.
Pioneer 610- was a runner- Like new chain
Homelite original E-Z- Full wrap, did run.
Mac D-36- Did run, has manual thumb pumper on the front
Dayton 2z461- did run, cracked cast inside muffler half- no bar
Montgomery Ward 2.8- Isnt locked up
Mac 1-43
Mac 250- early yellow top. Missing a few parts(mostly bolts)

All for swap. Looking for things that go bang, or ammo.
Also 288 parts.

 

[little possum]

Also have a set of Buckingham steel permanent tree gaffs with leather L pads. The straps should probably be replaced.
And I have a Bashlin climbing saddle. In good condition.


GONE!!! ^^

 

[Mastermind]

How many do you want? I have several brand new 14" or 16" GB bars for the little Homelites that use the square hole mount pattern?

I've got one on the way. But could use another.

 

[roncoinc]

Homelite muffler

Need one of these for a friend.
notice how the bolt holes are offset ??
goes on a cheapy homeowner.one of the $99 red and black ones

this is like the second or third time i tried here.
1/2 the price of the saw to buy a new one !

 

[Mastermind]

Need one of these for a friend.
notice how the bolt holes are offset ??
goes on a cheapy homeowner.one of the $99 red and black ones

this is like the second or third time i tried here.
1/2 the price of the saw to buy a new one !

No way to fix it with some welding Ron?

 

[Duke Thieroff]

Might trade this 3120 out, looking for old mag and cash


Pics and info can be found here

http://www.arboristsite.com/chainsaw/178676.htm



Chris

If you have a crank PM me.


If you don't then offer me some crumpled paper or a trade or both!



Chris

 

[roncoinc]

No way to fix it with some welding Ron?

NNooooooooooooooooooooooooooooooooooo......................
back side where it mounts to jug all ripped up to,weld get in the way.
somebody must have one !! am i the ONLY one that collect junk ??

 

[tbone75]

NNooooooooooooooooooooooooooooooooooo......................
back side where it mounts to jug all ripped up to,weld get in the way.
somebody must have one !! am i the ONLY one that collect junk ??

Ron would you like the whole saw?I got 2 that both run LOL Ranger & Bandit 33cc Edit : They don't fit!Dam!

 

[tomdcoker]

Stihl 041 rewind/fuel tank.

I need one of the above. There must be different types of these. The one that I need has the recessed area (see X in the picture). As you can see the flange that covers the flywheel is broken. So if you have one that this part is good I can take the two and make one good one. Thanks Tom P S will someone please open the picture for me.

Please P M me if you have one. Tom

 

[roncoinc]

I need one of the above. There must be different types of these. The one that I need has the recessed area (see X in the picture). As you can see the flange that covers the flywheel is broken. So if you have one that this part is good I can take the two and make one good one. Thanks Tom P S will someone please open the picture for me.

Please P M me if you have one. Tom

hows that tom ?
btw,you have a coil for an 020avp ?

 

[tomdcoker]

hows that tom ?
btw,you have a coil for an 020avp ?

Thanks for opening the picture. I have a coil for 031, 044, 034 I think, but I do not know if it will work on thwe 020avp. My IPL does not list the 020avp. If you think it will work let me know and I will check to be sure. Thanks again. Tom

 

[barneyrb]

I know this is a million to one shot but here goes, I need a complete air filter assy for a McCulloch 7-55 2 man saw. Have parts or $$$$$ to trade.

 

[Mastermind]

I looking for a carb to air filter elbow and a 24" or so bar for a Dolmar 119. I have parts and nasty dollars.