Swap meet...

[Duke Thieroff]

Need a chainbrake handle for a 385xp. One from a 390xp will fit.



Chris

 

[sefh3]

I'm looking for a choke rod, throttle rod and clutch cover for a Stihl 023. I'm thinking 021,023, 025 all would work. I have parts to trade.

 

[bcorradi]

Anyone have an 066/660 crankcase (poly flywheel) with preferably good bearings they'd like to part with? I have misc. stihl stuff and greenbacks to trade.

 

[PogoInTheWoods]

Still scrounging for a John Deere 80EV sprocket cover. An Echo CS750-EVL is the same saw, so....

Thanks for any leads. Doin' this for an old-timer neighbor.

Poge

 

[TRI955]

Need the carb elbow assembly and air filter for a Husky 359/357 Jonsered 2159...

Could also use a non-cat muffler too!!!

 

[tbone75]

Any one happen to have a air filter with screws for a Poulan 3300?Got a little to trade or green backs.This is for a saw I am giving to a buddy of mine.

 

[Modifiedmark]

Still scrounging for a John Deere 80EV sprocket cover. An Echo CS750-EVL is the same saw, so....

Thanks for any leads. Doin' this for an old-timer neighbor.

Poge

Do yourself a favor and quit looking for a 750 cover. There always broken. Find one from a 602 or 702, there shorter on the bottom but hold up alot better.

 

[blsnelling]

I'm looking for a early 10mm 044 cylinder. These are the ones with the angled cylinder fins.

 

[parrisw]

I'm looking for a early 10mm 044 cylinder. These are the ones with the angled cylinder fins.

I'll sell ya a whole really nice old 044, but it ain't cheap!

 

[huskydude]

I'm looking for a junk 372xp cylinder. Anyone got one in the scrap pile they would send my way?

 

[PogoInTheWoods]

Do yourself a favor and quit looking for a 750 cover. There always broken. Find one from a 602 or 702, there shorter on the bottom but hold up alot better.

Thanks for the tip. I know exactly zero about these saws except that the 80EV was a re-badged CS750 and a neighbor has one in great shape (minus the sprocket cover) that he wants to get running again while he can still lift it!

So...

Anyone have a 602 or 702 sprocket cover to part with?

Poge

 

[srcarr52]

I'm looking for a junk 372xp cylinder. Anyone got one in the scrap pile they would send my way?

I got a couple. You want a little al transfer or a lot?

 

[Modifiedmark]

Thanks for the tip. I know exactly zero about these saws except that the 80EV was a re-badged CS750 and a neighbor has one in great shape (minus the sprocket cover) that he wants to get running again while he can still lift it!

So...

Anyone have a 602 or 702 sprocket cover to part with?

Poge

I had a cover from a 602 but its now on my 750.

Well at least I think I still have a 750, I loaned it to a guy and he wants to buy it, so I put a price on it. Waiting to hear back...

 

[Warped5]

Mac 10-10A recoil part ....

Needing two (2) hold-down screws for a Mac 10-10A recoil.

Part number is 110646, specs are: Screw - Oval hd 8-32 x 1-1/8

Thanks!

 

[Glockman]

066

I'm looking for an 066 that has all parts but needs repair or rebuild.

Thanks
Dan

 

[Warped5]

I'm looking for an 066 that has all parts but needs repair or rebuild.

Thanks
Dan

(Shameless plug time again ....)

 

[timberdollars]

Stihl 020 avp flywheel

lookin for a flywheel or parts for early 020 avp points! Need some starter prawl springs for a couple of mine, easier to replace whole flywheel at this rate. so 1 maybe two flywheels or whole parts saws.
Also parts in general for 020av

Have a few trade parts left but not much, stained/tainted paper stuff too.

Also always looking for PARTNERS STILL! all the way through 2083/505 saws.

 

[tbone75]

lookin for a flywheel or parts for early 020 avp points! Need some starter prawl springs for a couple of mine, easier to replace whole flywheel at this rate. so 1 maybe two flywheels or whole parts saws.
Also parts in general for 020av

Have a few trade parts left but not much, stained/tainted paper stuff too.

Also always looking for PARTNERS STILL! all the way through 2083/505 saws.

Just wanted to let you guys know.I traded some saws with timberdollars and did very well!! Hes good to go!

 

[komatsuvarna]

Probably a long shot, but anyone have a fuel tank for a MS460?

 

[Mastermind]

I need a good carb for an 044/046. I've got one that will not be repaired here.