Swap meet...

[Modifiedmark]

It's got the heated handles also.

Yes it did, and that reminds me, anyone got a set of heated handle tubes for a Partner 5500H? :hmm3grin2orange:

 

[Stumpys Customs]

I'm finding myself in need of a Husky 3120xp cylinder. :help:

 

[sefh3]

I'm finding myself in need of a Husky 3120xp cylinder. :help:

Did you take a little too much off the one you have?

 

[Stumpys Customs]

Did you take a little too much off the one you have?

No, the porting came out great. It developed an air leak at the cyl base. :angry2:
I might be able to save the cyl, but would rather start fresh.
Ya win some, ya lose some:redface:
Just wish it happend on a less expensive saw.

 

[sefh3]

No, the porting came out great. It developed an air leak at the cyl base. :angry2:
I might be able to save the cyl, but would rather start fresh.
Ya win some, ya lose some:redface:
Just wish it happend on a less expensive saw.

I hear ya. I'm still hesitant to pull the dremel trigger on an MS290 that I have.

 

[stihl_collector]

I'm in need of a ms460/046 cylinder, prefer genuine. Please pm me.

Have a few bits to swap or cash.

 

[tbone75]

I have 2 350 Huskys to trade or sell.Up graded pistons nice and clean saws.18' B&C.Looking for a Husky 365builder or 372 builder or 034 builder 038 builder 044/046 builders.And Dolmars

 

[young]

I'm in need of a ms460/046 cylinder, prefer genuine. Please pm me.

Have a few bits to swap or cash.

your inbox is full

 

[sdmaker]

I have 2 350 Huskys to trade or sell.Up graded pistons nice and clean saws.18' B&C.Looking for a Husky 365builder or 372 builder or 034 builder 038 builder 044/046 builders.And Dolmars

18 foot bar and chain dang

 

[kuhndog]

TS 400 coil

Looking for good 3 bolt (older style) for a TS400 .Send a PM not much to trade.Thanks,David

 

[tbone75]

Looking for good 3 bolt (older style) for a TS400 .Send a PM not much to trade.Thanks,David

If its the same as my TS350 good luck?

 

[Work Saw Collector]

Is this the thread for Black Friday door buster specials on 048 parts? :hmm3grin2orange::hmm3grin2orange::hmm3grin2orange::hmm3grin2orange:

 

[MnSam]

Looking for an 038 gas tank/handle. I am willing to pay.

 

[Modifiedmark]

This is probably a wase of effort, but I would like to find all the chainbrake parts for my Dolmar 133.

Anyone got a donor saw or the parts?

 

[Mastermind]

I have 2 350 Huskys to trade or sell.Up graded pistons nice and clean saws.18' B&C.Looking for a Husky 365builder or 372 builder or 034 builder 038 builder 044/046 builders.And Dolmars

I have a great running 034 I built for some guy named John. He ended up with a 346xp instead........... Now I'm sitting on this 034....trying to decide if I should port it or not.

Of course I would need three Husky 350s for this saw.

 

[tbone75]

I have a great running 034 I built for some guy named John. He ended up with a 346xp instead........... Now I'm sitting on this 034....trying to decide if I should port it or not.

Of course I would need three Husky 350s for this saw.

:hmm3grin2orange: Can't say I would go for that? One plus a little I would think about :hmm3grin2orange: That and I still don't know if I did the right thing there yet?Can't try this saw out!

 

[Arrowhead]

Still looking for 038 plastic and starter cover.

 

[plumbcrazyjr]

Im putting up my dolmar 120si up for sale or trade. I ported it and pop-up on piston I have all the timing numbers if interested. She pulls 190lbs comp and runs very well just dont need another <70cc saw. I have put larger bar studs in it so i could run a stihl bar.

dont really know what i want for trade but open to all offers

 

[timberdollars]

Husqvarna 141 LE New Never seen Wood

Bought this NEW 141Le for my other half but she can't start it so its on the chopping block!!!! New never touched wood!!!! I did adjust the carb from the Horriffic Lean setting to a NICE EASY Starting setting that a saw should have.
Complete with 16" 3/8" Lp B/C

Trade for Compression Release 350, 55, J-Red Comp release parts saw
Part trade for ? something easy to start
Or the 175 greenbacks I invested

Sorry won't let me upload pics right now!!!!!!!!

 

[NeoTree]

I've got a brand new Max Flow setup for ms460/046 I bought last year but never used. Might trade for a new ES bar, a 36" or 42" loop of .063 or green. Check for pics in the classifides