Swap meet...

[Duke Thieroff]

I'll up the ante- two 150 parts saws, three XL-101 starters, a Super EZ muffler, and an Echo 650 muffler.

Keep all the other stuff, but send that winch and the SEZ muffler and ill have it out tomorrow.

 

[nmurph]

Bumpy on this.

Also looking for a clutch cover for a 288, a pretty one would be nice, bare or with brake junk is of no concern.

I'll trade you one for that shinnediwah. I might even through in the most of the rest of the parts to make it a runner.

 

[Eccentric]

Homelite XL-101: 160 p.s.i. compression, no spark, likely needs carb rebuild from sitting. Has a 20" hardnose original Homelite bar. I'm interested in trades for older McCulloch saws over 3 cubes, no plastic models. PM me with interested offers. Thanks

View attachment 277647View attachment 277648

PM sent.


Looking for a set of Pro Safety (or other aftermarket) spikes (inner and outer) for a 268/272XP Husky.............or at least a stock outer spike for the same saw. Only have the inner on it now. got old Homelite, Poulan, and McCulloch parts (and electronic substitutes for green government paper) to trade...

 

[brian660]

i`ve got a few bars I wanna get rid of before I leave for work, two 25inch and one 20inch, all roller nose, the 20 and one of the 25`s are stihl rollomatic, the other I can`t remember the brand but its grey and stamped made in Canada.

i`m up for anything your willing to trade for em.

 

[Trx250r180]

looking for a 990 remington saw complete runner would be nice





:msp_wink:

 

[Jacob J.]

looking for a 990 remington saw complete runner would be nice





:msp_wink:

lolol...good luck. I've been looking for years.

I gotta dig you out an 056 case tonight too.

 

[thomas1]

looking for a 990 remington saw complete runner would be nice





:msp_wink:

The only one i have has a long roller nose bar, would that be okay?

 

[thomas1]

lolol...good luck. I've been looking for years.

I gotta dig you out an 056 case tonight too.

JJ, do you have any background on the Remingtons?

 

[Jacob J.]

JJ, do you have any background on the Remingtons?

Not too much, other than they bought Mall Chainsaw manufacturing and got a lot of their design and engineering from Mall.

I have a 770 Super and a Super 880 that I need to restore.

 

[MS460WOODCHUCK]

I am in the need for a poulan S25DA clutch and 3/8lp drum/sprocket with bearing. I could also use a flywheel with the starter catchers (or whatever you call them) on it for the same saw. PM me if ya can help me out.

 

[tomdcoker]

I am in the need for a poulan S25DA clutch and 3/8lp drum/sprocket with bearing. I could also use a flywheel with the starter catchers (or whatever you call them) on it for the same saw. PM me if ya can help me out.

PM your address. I have a NOS flywheel. None of the other parts. Tom

 

[Trx250r180]

The only one i have has a long roller nose bar, would that be okay?

know anyone that restores those old saws ?

 

[Wagnerwerks]

i`ve got a few bars I wanna get rid of before I leave for work, two 25inch and one 20inch, all roller nose, the 20 and one of the 25`s are stihl rollomatic, the other I can`t remember the brand but its grey and stamped made in Canada.

i`m up for anything your willing to trade for em.

Do the 25s both have the big mount slot?

 

[Warped5]

know anyone that restores those old saws ?

PM sent

 

[Warped5]

Bumpy on this.

Also looking for a clutch cover for a 288, a pretty one would be nice, bare or with brake junk is of no concern.

Didn't you have a deal done with barneyrb last night?

He didn't withdraw his offer did he?

:confused2:

 

[Duke Thieroff]

Didn't you have a deal done with barneyrb last night?

He didn't withdraw his offer did he?

:confused2:

Ted,

I pulled out. I didn't want to short change him. Homie XLs and 150s are worth a ton.

 

[barneyrb]

Didn't you have a deal done with barneyrb last night?

He didn't withdraw his offer did he?

:confused2:

Ted,

I pulled out. I didn't want to short change him. Homie XLs and 150s are worth a ton.

No, he thought he was gettin to me so I let him out. I still have the 150 though, little rough, A/v sorta lame, and it needs a bar.........

 

[psuiewalsh]

I am in the need for a poulan S25DA clutch and 3/8lp drum/sprocket with bearing. I could also use a flywheel with the starter catchers (or whatever you call them) on it for the same saw. PM me if ya can help me out.

Will this guy work?

 

[Duke Thieroff]

No, he thought he was gettin to me so I let him out. I still have the 150 though, little rough, A/v sorta lame, and it needs a bar.........

I'll trade you four clapped out Cracker Jack toys and a gently used .354 pitch rim and bar for a Mac 1-10.

Duke

 

[AU_K2500]

OK. One case and crank is gone, along with the 024 AF cover

Found most of what I needed. Now just looking for 2 026 air filters, muffler, and a clutch cover.

Just went through the parts been. Lots of good stuff left to.trade including a nice 024/6 tank handle

The needed parts are:
2 026 air filters
1 024/6 muffler
1 clutch cover
1 clutch bell