The Official "Noodles" Pic and Vid Thread

[blsnelling]

<object width="640" height="385"><param name="movie" value="http://www.youtube.com/v/yXarLvnBbRs&hl=en_US&fs=1&rel=0"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/yXarLvnBbRs&hl=en_US&fs=1&rel=0" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="640" height="385"></embed></object>

 

[woodguy105]

Now that's making noodles!

 

[DSS]

Cool, how about some love for the 141!

Tried to to rep you, but can't. Can someone please ring him up for me?

gotcha.

 

[cpr]

gotcha.

Thanks, it let me get you instead.

 

[Hddnis]

Cool, how about some love for the 141!

Tried to to rep you, but can't. Can someone please ring him up for me?

Got 'em!


Mr. HE

 

[Andyshine77]

Did some noodleing with a ported 064 + 28" bar and new chain. This was the first run with the saw after machining a .040 pop up piston, compression is a healthy 165 and it should go up a bit. I had to torque on the saw pretty hard to pull it down, if I let it self feed the rpm's would hardly drop. I plan on making another video with the saw running an 8 pin sprocket.

<object width="640" height="385"><param name="movie" value="http://www.youtube.com/v/Ayk1MfzqX9I?fs=1&amp;hl=en_US"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/Ayk1MfzqX9I?fs=1&amp;hl=en_US" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="640" height="385"></embed></object>

 

[parrisw]

Did some noodleing with a ported 064 + 28" bar and new chain. This was the first run with the saw after machining a .030 pop up piston, compression is a healthy 165 and it should go up a bit. I had to torque on the saw pretty hard to pull it down, if I let it self feed the rpm's would hardly drop. I plan on making another video with the saw running an 8 pin sprocket.

Dang that saw really runs well Andre

 

[Stihlman441]

MS880 rounds and noodles.

 

[Stihlman441]

MS660 noodles.

 

[Andyshine77]

Dang that saw really runs well Andre

Thanks, but Brad did the porting and Nik did the machine work, I just stood over their shoulders telling them how it really should be done lol.

I made a mistake it's actually a .040 pop up, I edited the original post. :monkey:

 

[Stihlman441]

MS880 36'' bar comparing full comp (first) and skip chain NOODLES at the end,notice the sap in this ossy Stringybark.

 

[blsnelling]

Did some noodleing with a ported 064 + 28" bar and new chain. This was the first run with the saw after machining a .040 pop up piston, compression is a healthy 165 and it should go up a bit. I had to torque on the saw pretty hard to pull it down, if I let it self feed the rpm's would hardly drop. I plan on making another video with the saw running an 8 pin sprocket.

That thing looks to be holding is RPMs really well now. BTW, that 064 is wearing a Mahle 066 topend. No decomp on that bad boy

 

[Andyshine77]

I actually have a good bruise from starting that thing lol.

 

[Zombiechopper]

Did some noodleing with a ported 064 + 28" bar and new chain. This was the first run with the saw after machining a .040 pop up piston, compression is a healthy 165 and it should go up a bit. I had to torque on the saw pretty hard to pull it down, if I let it self feed the rpm's would hardly drop. I plan on making another video with the saw running an 8 pin sprocket.

<object width="640" height="385"><param name="movie" value="http://www.youtube.com/v/Ayk1MfzqX9I?fs=1&amp;hl=en_US"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/Ayk1MfzqX9I?fs=1&amp;hl=en_US" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="640" height="385"></embed></object>

Idiot!!

only used TWO fingers on the cap!! Everyone knows its a THREE %^(&ing FINGER CAP! I can't believe some people!
Idiot!!

Saw looks slow. Bar is too long. Dude needs to shave

 

[parrisw]

Thanks, but Brad did the porting and Nik did the machine work, I just stood over their shoulders telling them how it really should be done lol.

I made a mistake it's actually a .040 pop up, I edited the original post. :monkey:

At any rate, it runs real nice. Good work Brad and Nik.

Then why does Andre get all the fun or running it.

Idiot!!

only used TWO fingers on the cap!! Everyone knows its a THREE %^(&ing FINGER CAP! I can't believe some people!
Idiot!!

Saw looks slow. Bar is too long. Dude needs to shave

ha ha ha ha ha ha ha haha

 

[Andyshine77]

Idiot!!

only used TWO fingers on the cap!! Everyone knows its a THREE %^(&ing FINGER CAP! I can't believe some people!
Idiot!!

Saw looks slow. Bar is too long. Dude needs to shave

OK that was funny, I think I peed a little.

BTW You forgot, no chaps as well.

 

[Andyshine77]

At any rate, it runs real nice. Good work Brad and Nik.

Then why does Andre get all the fun or running it.

Because I have hard wood!!

 

[parrisw]

Because I have hard wood!!

I don't care to know what you Brad and Nik do on your free time.

 

[Andyshine77]

What happens at Nik's shop stays in Nik's shop.:blush:

 

[parrisw]

What happens at Nik's shop stays in Nik's shop.:blush:

ha ha ha OMG