Vintage Chainsaw Museum

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
...there was one saw in the batch (that CAD day back in 2012) sold by Montgomery Wards that I gave away, but really wish now that I had kept...

DSC00504.JPG


Some guys knew of my remorse over that saw and sent me a eBay listing a while back.

1732023758391.png


It took a while but the saw arrived yesterday. I don't think it has ever been fueled and run, but sadly the chain is missing.

20241119_065805.jpg


There are a few differences in the two saws, the one I had earlier with a later serial number (85X) had a pulse operated fuel pump and a lever connected to the throttle handle that operated the manual oiler button. The latest one (Series number 6X) doesn't have either of those features.

DSC00579.JPG


20241119_065849.jpg


It looks like 6X had that lever at one time but it has since disappeared. I think I may be able to fab up something that would look correct.

Mark
 
Just imagine when that saw was new, people must have felt like it was the peak of technology and progress. I wonder if that was one of the first saws with that style of chain? According to Mike Acres site the powerhead can pivot 360 degrees on the handle (I think).
 
Just imagine when that saw was new, people must have felt like it was the peak of technology and progress. I wonder if that was one of the first saws with that style of chain? According to Mike Acres site the powerhead can pivot 360 degrees on the handle (I think).
Yes, it does. I was amazed to see that when prepping it for shipping.
Can set it for felling and bucking in seconds.
 
I've been busy working on saws (a few for myself, mostly for others) and haven't updated the expansion project in a while.

Old building was demolished and the rubble hauled away.

20241111_163152.jpg

I think he hauled in 12 loads of dirt to fill the hole.

20241113_113710.jpg

After proper compaction, they dug in the water service and sanitary sewer. The water required removal of several feet of the street in front of the poperty.

20241122_071322.jpg

Trenches for the footing were dug last week, footing were poured today.

20241216_074419.jpg


20241216_083812.jpg

The ICF (insulated concrete forms) were set this afternoon and the frost wall will be poured tomorrow. That's all we will be able to accomplish this year, can't risk pouring the floor and having the frost heave it up.

Mark
 
I have managed to get a few more saws cleaned up and moved up into the display.

Stihl 056 Super, the combi-can fuel tank tool box was a gift from Srcarr52.

20241214_165718.jpg

20241216_085517.jpg

This Wright B-100 is based on the Poulan 306 and has a complicated gearbox with crankshaft to drive the blade. The gearbox was locked up when I got it, turns out someone had not adequately tightened the connecting rod bolts in the gearbox and the cap loosened up and turned the needles loose. I could not find any bearings with similar small diameter needles (0.040") so I bought a few 1mm drill bits off Temu and cut them to length. Everything seemed to move as expected but I did not have the confidence to fuel it up and run it. It does run on prime...

20241219_103802.jpg

20241219_103817.jpg

Last one completed was this Lombard 34. I wish I had taken a few more photos during the process...hollow shaft output shaft is splined for the drive sprocket, cross drilled, and the other end of the shaft terminates within the oil tank. As the shaft rotates, a "screw" attached to the oil tank pushes oil down the shaft and out at the sprocket to lubricate the chain. The float style carburetor is mounted at a 45 degree angle so it theoretically will operate upright for bucking cuts or horizontally for felling cuts.

20241219_103433.jpg

20241219_103534.jpg

Mark
 

Been there done that. My issue was getting the sealing rings on the output shaft to seal. I had got NOS ones but think they were too old and hard. BTW your saw is a 68 or 69 model as it has the combo decomp switch button and 5mm plug wire. They also have a carb with a smaller venturi then the chainsaw to keep the speeds down on them

Print this out for your display. We need to find a electric start model.
 

Attachments

  • Wright blade saw brochure.pdf
    7.2 MB

Latest posts

Back
Top