I looking for some ideas for carrying wood with a 3 point carry-all. What I built is way too unstable. Tractor has too much side to side movement.
Ian
Ian
Show me your 3-point wood haulers
- Thread starter Haywire Haywood
- Start date
Help Support Arborist Forum:
Guido Salvage
Supreme Saw Whoreder
Not sure how the 3 point is set up on your Kubota, but you might just need a set of sway bars for it. I have the same trouble towing a trailer if I use one of those 3 point drawbars.
Check on e-Bay and see what you find.
Check on e-Bay and see what you find.
It's got turnbuckles to stop the lift arms from going back and forth, the side to side is the whole tractor as it crosses uneven ground. I think part of the solution would be to make two short rows instead of one tall one like I have.
Ideally, what I end up with will pin together in such a manner that I can unpin it and hang it relatively flat on the barn wall to conserve space. I could just make a box from pallets but that would be bulky.
Gotta put my thinkin' cap on. I better check the batteries first, they're probably dead from sitting unused for so long.
Ian
Ideally, what I end up with will pin together in such a manner that I can unpin it and hang it relatively flat on the barn wall to conserve space. I could just make a box from pallets but that would be bulky.
Gotta put my thinkin' cap on. I better check the batteries first, they're probably dead from sitting unused for so long.
Ian
Guido Salvage
Supreme Saw Whoreder
Ian,
How is the pallet attached to your 3 point hitch? If it were me, I would go down to your local TSC, SS, F&F etc. and get a 3 point hitch carryall and build a box on the frame for holding your wood. The image below shows what one looks like.
Gary
How is the pallet attached to your 3 point hitch? If it were me, I would go down to your local TSC, SS, F&F etc. and get a 3 point hitch carryall and build a box on the frame for holding your wood. The image below shows what one looks like.
Gary
Last edited:
There's homemade version of that under there, but it's made of 1.5" square tube instead of angle.
Ian
Ian
dingeryote
Blueberry Baron
Haywire,
Your COG is waaay too high with that load like that.LOL!!
Didja pucker the vinyl on the seat?
Run the weight further to the rear instead of upwards.
A couple old chunks of concrete in the loader to keep the front on the ground, or a front basket full of more rounds if you're up to fabbing.
I don't know the lift arm capacity on those little 'botas, but you might eyeball it, and keep it in mind.
A good heavy duty trailer might be in your future.
Stay safe!
Dingeryote
Your COG is waaay too high with that load like that.LOL!!
Didja pucker the vinyl on the seat?
Run the weight further to the rear instead of upwards.
A couple old chunks of concrete in the loader to keep the front on the ground, or a front basket full of more rounds if you're up to fabbing.
I don't know the lift arm capacity on those little 'botas, but you might eyeball it, and keep it in mind.
A good heavy duty trailer might be in your future.
Stay safe!
Dingeryote
Haywire,
Your COG is waaay too high with that load like that.LOL!!
Didja pucker the vinyl on the seat?
Nah, I'm too stooopid to know when to pinch plugs out of the vinyl. LOL
Yea, I'll work on that tomorrow. Half height, double row.
1210 lbs
A good heavy duty trailer might be in your future.
I want to avoid a trailer if at all possible. We'll see. I'll figure out something if I don't kill myself first.
My wife will be royally PO'd if I die and stick her with the payment.Ian
Last edited:
wdchuck
Addicted to ArboristSite
.
.
.
<---------works quite well.
.
.
<---------works quite well.
I think your tractor size is going to limit you quite a bit on the amount you can haul , my 2010 john deere acts like it has all it can handle with a full pallet stacked to the top and its alot bigger than the kubota .
IPLUMB
ArboristSite Operative
Have you seen these videos? I plan on going this rout some day. http://wilsonoutdoors.com/index.php?option=com_content&task=view&id=170&Itemid=71
my father has the same carry-all on his bx2350. we just put a pallet on it and lift. you can stack 2 rows deep and about 2-2.5' high and that's about all it will lift because it moves the weight further back. simple and cheapIan,
How is the pallet attached to your 3 point hitch? If it were me, I would go down to your local TSC, SS, F&F etc. and get a 3 point hitch carryall and build a box on the frame for holding your wood. The image below shows what one looks like.
Gary
Swamp Yankee
Addicted to ArboristSite
Hope you're on flat ground
I had the same tractor before I went to a B-Series. Do not remove the belly mower. It weighs about 300 pounds keeping the center of gravity of the tractor low. The deck also acts as a sort of outrigger to keep the tractor from testing the structural integrity of the roll bar. Learned two things when that happened, the engine doesn't like to run on its side and fat old men can really jump when the need presents itself.
Take Care
I had the same tractor before I went to a B-Series. Do not remove the belly mower. It weighs about 300 pounds keeping the center of gravity of the tractor low. The deck also acts as a sort of outrigger to keep the tractor from testing the structural integrity of the roll bar. Learned two things when that happened, the engine doesn't like to run on its side and fat old men can really jump when the need presents itself.
Take Care
hoogie
ArboristSite Member
heres mine, bought a carry all from TSC for hundred then put the side on a skid with carrage bolts. But when the skid takes a dump, pull the 4 bolts lift the sides off put on a new skid bolt em and be done this moves a lot of wood better fill the bucket in the front if your gonna fill the box all the way up...And a full box keeps me goin for a week at a time.
http://www.arboristsite.com/attachment.php?attachmentid=160475&d=1291411185
Built the side and later found out the homemade pallet forks were too wide for the little pallet, so just laid it on top of forks. drove REAL slow.
Built the side and later found out the homemade pallet forks were too wide for the little pallet, so just laid it on top of forks. drove REAL slow.
branchbuzzer
Undiagnosed
Ok, this is what I ended up with for the firewood rack. It pins together with door hinges so it can come apart and stack flat. The back I rigged so it will swing open. Not the best, but it works. A buddy of mine welded 1/4" rod to the hinge pins so I'd have a handle for removing them but it's not working out, they're too tight and under some bind. It's a PITA to pull them. I think I am going to replace them with some big nails to make them easier to pull.
It doesn't sway all over the place, but it doesn't hold as much wood either. Good trade off.
It doesn't sway all over the place, but it doesn't hold as much wood either. Good trade off.
Last edited:
Thanks... I had several things in mind for the sign, but they had to be short to fit. "Mighty Mouse" and "Little Biggun" were in the running, but pushing the length limit to get letters of decent size.
Those letters are actually reflective to match the sign. A local sign shop did it up for $10.
Ian
Those letters are actually reflective to match the sign. A local sign shop did it up for $10.
Ian
Similar threads
