husky

New crank bearings, gaskets, seals, oem piston, rings. Runs and oils as it should. It does have some blemishes but should be a good runner. Would like $375.00 shipped to you.

This one has new skf bearings, oem piston & ring, gaskets, and fuel line. There is one hole that i repaired with a time-sert. As you can see the muffler is getting thin and there is a crack in clutch cover. This saw has not been in wood yet. Would like $425 shipped.

Yes another 385xp! This one has new Meteor piston & rings. Pull rope & steel insert along with carb kit. This one has been started, warmed, adjusted and rpms checked. Setting are set rich at this time. Havent had in any wood yet. There are some signs of wear as this is not a NOS saw! Anyway will...

Just trying to thin the hurd. Saw has new oem piston and rings, carb kit. AM cover and tank. Saw is not a shelf queen but is still a good running saw. Put a tank of fuel through it after piston install. $325.00 shipped

Forsale PHO. Saw has one tank on new rings. There is some scrapes and bruises as you can see. Some retard thought he needed to scratch his initials on clutch cover. Can swap full wrap for half if wanted. Asking $435 and ill pay for shipping.

Hello all, new user to the site, have lurked some forums. What a great place. Lots of helpful advice and tips. Little back ground. Husqvarna 254 professional serial number 8180663, I seem to have a dead coil. Saw is ancient but I love it. It rips! Compression check 130 psi cold 145ish...

I recently started having issues with my Rancher 55. Was cutting the other day, when after stopping for a bit, it refused to start. It seems that the saw is flooding, I can see lots of wetness on the sides of the piston from the exhaust port and the plug gets wet. If I turn the saw over, I...

Does anyone have a detailed picture or diagram of a husqvarna 36 carb and how it is installed? Mine is apart and I cant remember how to put it back together. Specifically the choke and throttle levers on the right side. Cant figure out how the spring and stuff goes back with the choke lever...

https://eauclaire.craigslist.org/grd/d/arcadia-husqvarna-3120xp-chainsaw-24/6806653714.html Seems reasonable...

hi if you own a husky 394 and would like to test a new free walbro wj71 send me a pm and i will hook you up. you will work directly with the vendor. send me a photo of the saw in the pm. one tester is needed. it sounds like they want to know if its a good carb that produces a solid response...

Looking for a flywheel for a project 395xp. Can anyone help a guy out?

I suppose it would be somewhere on here if it's possible, but I'll ask anyway. Are there any of the new Husqvarna flippy caps that will fit the 346XP? I don't have a problem with the regular caps, but think it would be a good update.

Everything is gone. Thanks gentlemen. I have two brand new Oregon Power Match 24" bars. This is Oregon's BEST bar and features a replaceable tip. They have the D009 (large Husky) bar mounting holes. Fits just about every Husqvarna / Jonsered / Dolmar / Makita larger than 60cc. They are 24"...

I picked up a few saws from a buddy with a tree service recently. I've been going over them slowly. I got a remanufactured mccollouch 2014 I think, it just says fr 2.0 needs a new flywheel key carb kit fuel lines etc. A old stihl 031AV so far I'm doing carb and fuel lines. And lastly a husqvarna...

I'll be buying the Husky 395xp. The best deal I have found is $1,099.00 from American Pride Power Equipment. That is brand new, and it doesn't specify a bar length. Is there a better deal out there? It doesn't necessarily need to be brand new, but something close to it that doesn't need any...

So a local guy has the 372 for sale he had a 395 he sold last week. We were talking chainsaw Mills. So he hits me up today and says I have a 372 for sale. Some of you that know me... know I don't like (avoided) Husqvarna because my old man ran them but I think for $300 I might just have to get...

Hi looking at buying an entry level Pole Saw, I have always used Sthil products in the past and am looking at this Pole Saw to be used 4 or 5 times during the year. https://cantrellhardware.stihldealer.net/products/pole-pruners/homeowner-pole-pruners/ht56ce/#specifications_tab I have seen many...

Im looking for the plastic air filter cover and the side cover on the bar side

Hello all, I am at a complete loss- my Husqvarna 394 chainsaw will start but immediately dies. It is a 1998 model. I have already tried the following: New Gas line New Fuel filter New Fuel tank vent New tank vent filter New Gas cap Put carb kit in it Cleaned the carb Air filter is...

Huztl is looking for a 288xp to study. They want it to be new or almost new. What they need is for you contact them with all the details. Address the message to the Manager. Use the message system on their website to make the initial contact. They ask me about this when they were wanting to take...