build off challange

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Ya Scott's cornhole.:hmm3grin2orange::hmm3grin2orange:

cornfield3.jpg
 
wow. worked hard all day to come back to see this.i see all the little girls on this site are trying to get this thread locked. some one said that i felt threatened because i didn't show my tools,my work, my setup, my numbers. most good builders don't. i think you girls are the ones that feel threatened. if you don't want to be called girls then don't act like one.


if any one still wants me to do the gtg let me know.
 
Racing is just like most other competitive ventures, whether it be saws, cars, motorcycles, firearm shooting events,etc, in the end to compete at the top levels, it just turns into a money game, how bad do you want to win, how deep is your pocket. It's easy to get caught up in it and when you come to you senses, you wish you had the pile off money you've spent back. The work saw build off may get boring to some, but I'd ten times watch a saw that will cut wood all day with off the roll chain than one than runs less than 10 sec. but that's just my opinion.
 
wow. worked hard all day to come back to see this.i see all the little girls on this site are trying to get this thread locked. some one said that i felt threatened because i didn't show my tools,my work, my setup, my numbers. most good builders don't. i think you girls are the ones that feel threatened. if you don't want to be called girls then don't act like one.


if any one still wants me to do the gtg let me know.

Sounds like a plan,,,, But I'm No builder,,, Just a hack on my ownstuff,,, for some reason the few I've done seem to run fairly well most of what I ve done on work/woodsported saws I was given advice from guys right here like DC, Jasha, JJ, SW and I have used some of my old 100cc piston ported kart motor tuning stuff I picked up along the way,,, I dont do race chains,,, not even,,,,,,,,

in the 460 buildoff I had never built/run a saw in a GTG competition til then,,, I think mine ended up third and i missed the tune up. It was slobbering Phat,,,

but I still had fun,,, Looking forward to Sconnieville in the spring
 
Last edited:
RiverRat2 said:
MY next Junk yard Dog,,, this ones going to ECopsey,,,, as soon as I can dig/mill the broken off LH screws out of the carby, it got run over by the skidsteer,, and almost lost in the beetle kill fire!!!
sigpic11978_1.gif

make sure you get a blue handle for that dolmar.:hmm3grin2orange:
 
wow. worked hard all day to come back to see this.i see all the little girls on this site are trying to get this thread locked. some one said that i felt threatened because i didn't show my tools,my work, my setup, my numbers. most good builders don't. i think you girls are the ones that feel threatened. if you don't want to be called girls then don't act like one.


if any one still wants me to do the gtg let me know.

I don't think anyone has an issue with you or your work Scott. I for one have grown sick of Paul's cheerleading though.

When he first got a Copsey saw he acted the same way. Then he brought it to a GTG and didn't have a clue how to run it. It was embarrassing to watch. I just hope he doesn't make your work look bad.
 
Then he brought it to a GTG and didn't have a clue how to run it.

Start engine
Squeeze throttle to WFO
Hold on for dear life


At least that's the method that seemed to work on a particularly well built 372xpw I recently ran at a gtg. The only way to slow it down was to shut it off. Pretty easy to run. ...?
 
Start engine
Squeeze throttle to WFO
Hold on for dear life


At least that's the method that seemed to work on a particularly well built 372xpw I recently ran at a gtg. The only way to slow it down was to shut it off. Pretty easy to run. ...?

It does seem simple don't it???? :hmm3grin2orange:
 
I screwed up one time at a GTG, I got a guys 2095 pinched. I looked like a big dork, well wait I am a dork. He just smiled and said jokingly "now I get to run YOUR saw".
 
Scott, I still would like to see the Cornholer GTG come off......count on me sending a chain if it does! Come on Cornhole Willie lets Race!........Hahahahahaha!
 
I don't think anyone has an issue with you or your work Scott. I for one have grown sick of Paul's cheerleading though.

When he first got a Copsey saw he acted the same way. Then he brought it to a GTG and didn't have a clue how to run it. It was embarrassing to watch. I just hope he doesn't make your work look bad.

i understand what your saying. paul is just proud/ excited about his saw. but why drive this thread into the ground? i feel it's aimed at me.
 
Scott, I still would like to see the Cornholer GTG come off......count on me sending a chain if it does! Come on Cornhole Willie lets Race!........Hahahahahaha!

Dennis,,, does this mean you are building my race chain????? Cause I sure as heck wouldnt know where to start,,,!!!! I'm a certified wood tick,,, not a racer but Im learning,,,,
 
Last edited:
i understand what your saying. paul is just proud/ excited about his saw. but why drive this thread into the ground? i feel it's aimed at me.

On the contrary Scott, we saved your thread.

It was getting nasty, so a few of us employed some humor to divert attention away from a few nasty posts.

As you can see, it's died back down again. :)

It works sometimes to save a thread from a premature lock, and I hope it did this time.

No disrespect toward you or your thread. :cheers:

All the infighting and bad blood (which often isn't even from here) gets old, and if derailing a thread for a bit, nips it in the bud, well. . . It's better than the alternative.
 
Back
Top