build off challange

[tlandrum]

heres the before porting and after the first round of porting onb my 385xp. i didnt think it was very impressive till i compared it to other saws.


[video=youtube;KJ1rzxWbWyc]http://www.youtube.com/watch?v=KJ1rzxWbWyc&list=UUqYITg6g1quHLq4YJfxj_qA&index=2&feature=plcp[/video]


here is the after port work video

[video=youtube;KJ1rzxWbWyc]http://www.youtube.com/watch?v=KJ1rzxWbWyc&list=UUqYITg6g1quHLq4YJfxj_qA&index=2&feature=plcp[/video]

 

[TK]

Bout a 2.2 second difference from this seat

 

[tlandrum]

there is not a good gain in speed of cutting but it gained a lot of torque. i think i should try it with an 8 pin i the same log now that it has the torque to pull it.

 

[Dennis Cahoon]

Dog that club in the wood......then you'll see if it has any torque!

 

[tlandrum]

heres the 8 pin video and the wood is a touch bigger than the 7 pin video
[video=youtube;RmarB-6B7NI]http://www.youtube.com/watch?v=RmarB-6B7NI&list=UUqYITg6g1quHLq4YJfxj_qA&index=1&feature=plcp[/video]

im getting about 12.66 on that cut

 

[RiverRat2]

heres the 8 pin video and the wood is a touch bigger than the 7 pin video

im getting about 12.59 on that cut

closer to 13 actually lol,,, but whose counting,,, quite an improvement over the seven pin really nice work bro,,,

 

[GrizzlyAdams86]

opcorn:
Just finshed reading all 60 pages. I can make it both days as of now. Probably spend most of it observing.

 

[tlandrum]

i went back and timed it 3 more times and i get 12.66. was slow on the start on the first go round lol

 

[andydodgegeek]

opcorn:
Just finshed reading all 60 pages. I can make it both days as of now. Probably spend most of it observing.

Holy! It would take like 17 hours to read all 60 pages.

 

[Metals406]

i went back and timed it 3 more times and i get 12.66. was slow on the start on the first go round lol

I got 14.98 stock, and 12.67 on the last vid.

 

[GrizzlyAdams86]

Holy! It would take like 17 hours to read all 60 pages.

Actully it was about 3 hrs, would have been closer to 2 if I didn't have to stop and laugh at some posts along the way. And load times too. (only have 50.6 Kbps of blazing fast dial-up here.)

 

[Hedgerow]

Actully it was about 3 hrs, would have been closer to 2 if I didn't have to stop and laugh at some posts along the way. And load times too. (only have 50.6 Kbps of blazing fast dial-up here.)

And we were all worried about the thread getting locked... Psshhh...
:msp_tongue:

 

[tree monkey]

[video]http://s155.photobucket.com/albums/s294/scottk66/?action=view&current=MVI_0030.mp4[/video]

 

[RiverRat2]

yo Homes,,,

i went back and timed it 3 more times and i get 12.66. was slow on the start on the first go round lol

I was just pulling your E string about your time,,, LOLOL!!! and drinkin a few of them dang Lime Beers you got me started on!!!!

I got 14.98 stock, and 12.67 on the last vid.

Yeah nearly 2.5 seconds is a big improvement

 

[wendell]

[video]http://s155.photobucket.com/albums/s294/scottk66/?action=view&current=MVI_0030.mp4[/video]

Good job, Scott.

 

[chainsawnut460]

Good job, Scott.

preety close to yours?

 

[chainsawnut460]

Good job, Scott.

dont mean to pry just curious

 

[parrisw]

[video]http://s155.photobucket.com/albums/s294/scottk66/?action=view&current=MVI_0030.mp4[/video]

Is that the before vid? :hmm3grin2orange:

 

[tree monkey]

Is that the before vid? :hmm3grin2orange:

what hapened to yours?

 

[parrisw]

what hapened to yours?

Just got back from holidays. Found a problem with the saw, so had to pull the tank off to try and fix it. Will know tomorrow if it's fixed or not.