Choosing a used chain saw

[Project man]

Hello, I'm in the market for a larger saw. Currently I have a rancher 450 which is good but I am looking for a stronger larger model for falling some oak and maple trees 18-24" in diameter. I want to take a look at 2 saws in my vicinity. There is a MS 361 and a MS 391 both available for @ the same cost. Obviously, the condition of the saw will be a big factor in this purchase. Is there any comments whether one is better than the other or if one is easier to use or is easier to service than the other? When I go to check out the saws, I wanted to bring a compression gauge to make sure the compression is good and was wondering what a good compression reading would be on saws of these displacements......thanks again for any comments and ideas!!

 

[Bob Hedgecutter]

I would not bother with the 391 and concentrate on the 361- much better made saw.
If it falls down the rope, leave it, if it slow chugs- take it.
Better to take a T27 wrench and look at the piston through the exhaust port than rely on compression testing.

 

[Bill G]

As Bob said......361

 

[SteveSr]

Hello, I'm in the market for a larger saw. Currently I have a rancher 450 which is good but I am looking for a stronger larger model for falling some oak and maple trees 18-24" in diameter. I want to take a look at 2 saws in my vicinity. There is a MS 361 and a MS 391 both available for @ the same cost. Obviously, the condition of the saw will be a big factor in this purchase. Is there any comments whether one is better than the other or if one is easier to use or is easier to service than the other? When I go to check out the saws, I wanted to bring a compression gauge to make sure the compression is good and was wondering what a good compression reading would be on saws of these displacements......thanks again for any comments and ideas!!

361 definitely. However you really need to know how to check over a used saw for other issues like a worn out bar, proper oiling. Also need to make sure that it is all original and not a flippin' saw with lots of Chinese parts including piston, cylinder, carb, air filter, etc.

Definitely pull the muffler to show the condition of the piston and cylinder. Look for blow-by on the rings and lots of carbon deposits from cheap oil / bad fuel. with a small flashlight you might be able to see the intake side of the cylinder when the piston is down.

You also want to pull the clutch drum so that you can inspect the crankshaft stub for scoring and the bearing for wear/integrity. If the crank stub is galled the saw is junk. You can get suspicious if the clutch drum has a bit of "wobble" in it.

Genuine Stihl parts should have the Stihl logo on them somewhere and or Stihl "xxxx-xxx-xxxx" part number on them.

 

[EchoShindaiwaMakitaDolmar]

If it was me, I'd buy a new Echo pro saw- the cs620p/pw, and be very happy with its performance and reliability.

 

[Del_]

Hello, I'm in the market for a larger saw. Currently I have a rancher 450 which is good but I am looking for a stronger larger model for falling some oak and maple trees 18-24" in diameter. I want to take a look at 2 saws in my vicinity. There is a MS 361 and a MS 391 both available for @ the same cost. Obviously, the condition of the saw will be a big factor in this purchase. Is there any comments whether one is better than the other or if one is easier to use or is easier to service than the other? When I go to check out the saws, I wanted to bring a compression gauge to make sure the compression is good and was wondering what a good compression reading would be on saws of these displacements......thanks again for any comments and ideas!!

The Stihl 036 is a good saw, too.

I see them come up for sale every now and then at low prices.

I picked up a 362C in good shape for $300 last year. I like it.

 

[Lionsfan]

I wouldn't buy either. Wait for something 70cc's to turn up.

 

[Bill G]

I wouldn't buy either. Wait for something 70cc's to turn up.

Yes, they cut nicely and keep your hands warm.
Kinda like a girl I knew in school

 

[dboyd351]

Husky 372 is a very good 70cc saw

 

[Project man]

Wow!! thanks so much for the feedback.....so the 391 is out and careful 361 inspection is in order, not to mention the other suggestions stated here. I'm kind of a brand loyal person and never owned s stihl saw but they seem to be used by many professionals and the parts are available if and whenever I have to tear a saw down in the off season. After looking at the piston for scratches, what would be a good compression # for the 361?

 

[SteveSr]

After looking at the piston for scratches, what would be a good compression # for the 361?

Compression number is irrelevant unless the rings are stuck which should be rather obvious from the visual inspection.