FarmerTec Huztl MS660 Updated Build Kit - Build Thread

[Rick Stephens]

Wow, these AM cylinders are all over the place for dimensions. The thickness of three layers of printer paper is all I need (in addition to a regular gasket). I'm going to make a slug with my 3D printer and cut the squish band with sand paper and use the metal gasket. At least that's my plan at the moment while I sit here at work thinking about saws

I take you have never tried to file or sand on nikasil before. Ain't happening my friend.

 

[Bedford T]

The pto bearing needs to go through .040 because it fits up against the oil pump. When I install the bearing I put an oiler without the piston and bolt on the case and heat the case and bearing falls right into the indention on back of oiler,thus it can't fall through plus it is exactly where it needs to be.

You are confusing it with the 440. The 660 does not depend on the oiler.

chainsaw kits and packing lists
http://thechainsawkitguy.com
http://YouTube.com/c/the1chainsawguy

 

[gary courtney]

You are confusing it with the 440. The 660 does not depend on the oiler.

chainsaw kits and packing lists
http://thechainsawkitguy.com
http://YouTube.com/c/the1chainsawguy

No sir I am not ! I just finished building 2 oem 660's complete. The bearing goes through the case approx. .040 as I stated. afleetcommand aka. @weimedog video as well as @Mattyo video touch on this. Go to 18:48 in video .

 

[Slick50]

You are confusing it with the 440. The 660 does not depend on the oiler.

chainsaw kits and packing lists
http://thechainsawkitguy.com
http://YouTube.com/c/the1chainsawguy

You are incorrect . The bearing does seat up against the oiler indention. Why doe you think they put the recess in there in the first place. @gary courtney is correct! But you can't tell a know it all anything.

 

[grizz55chev]

You are incorrect . The bearing does seat up against the oiler indention. Why doe you think they put the recess in there in the first place. @gary courtney is correct! But you can't tell a know it all anything.

Careful, he’ll put you on ignore!

 

[Slick50]

Careful, he’ll put you on ignore!

He has got to be the most pompous a-hole I ever encountered on a forum. Never seen him admit he was wrong. Gary was too nice in his response.

 

[grizz55chev]

He has got to be the most pompous a-hole I ever encountered on a forum. Never seen him admit he was wrong. Gary was too nice in his response.

I concur, whole heartedly.

 

[Bedford T]

oh look an HL ad

i have never had the problem you are suffering from or your idols, nor has anyone ever posted about this.

I dont care what they said. I built many kits and think i got all this started. I was speaking directly to the use of the oiler not being important in relation to the bearing ("The pto bearing needs to go through .040 because it fits up against the oil pump"). anyway the bearing comes installed. There is an indent, this is like... let me think of something to find wrong... when there is not a issue, unless they sent a bunch out the door that dont have bearings and seals installed.

this gets more bizarre by the day.

No sir I am not ! I just finished building 2 oem 660's complete. The bearing goes through the case approx. .040 as I stated.

 

[gary courtney]

or your idols,

You are one condescending person. The way you relate to people is very disturbing. You must be a hoot at family reunions. I watched your video and saw you drop the bearing completely through the case. If you would have had the oil pump as a guide that would not have occurred.

 

[Bedford T]

You are one condescending person. The way you relate to people is very disturbing. You must be a hoot at family reunions.

If defending accurate information is being condensing then I can live with that. Telling a new builder to pay attention to the indent in bearing installation would have been helpful.

chainsaw kits and packing lists
http://thechainsawkitguy.com
http://YouTube.com/c/the1chainsawguy

 

[gary courtney]

If defending accurate information is being condensing then I can live with that. Telling a new builder to pay attention to the indent in bearing installation would have been helpful.

chainsaw kits and packing lists
http://thechainsawkitguy.com
http://YouTube.com/c/the1chainsawguy

with pump installed as a guide would prevent the bearing from falling through as did in your video.

 

[Slick50]

from or your idols

So if someone quotes you are does as your videos state you become their idol?

bizarre

The only thing "bizarre" is you Baby Huey !

 

[Bedford T]

with pump installed as a guide would prevent the bearing from falling through as did in your video.

I recall no video on 660 bearing installation. Thinking back it has a lip.

http://thechainsawkitguy.com
https://www.youtube.com/the1chainsawguy

 

[TreeJoe]

dude you are bizarre u follow him around like a baby. get a life. you are trying so hard to be a jerk and you are killing it. several of you follow him around and take pot shots. I would say your sole purpse is to live in his shadow.

So if someone quotes you are does as your videos state you become their idol?
The only thing "bizarre" is you Baby Huey !

 

[gary courtney]

I recall no video on 660 bearing installation. Thinking back it has a lip.

http://thechainsawkitguy.com
https://www.youtube.com/the1chainsawguy

12:50 into video. Oil pump installed w/o piston and bolt would have prevented this. Just sayin.

 

[TreeJoe]

u like psting videos why not post the video of him screwing this bearing up. or did you get it mixed up with somebody elses videos. i built 2 660 using his videos as other people have. i did not c that. i need info I can count on.

with pump installed as a guide would prevent the bearing from falling through as did in your video.

 

[Chainsaw Jim]

Is this all happening because of this whole snowflake generation thing? What happened to man who doesn't give a chit and says "............".

Yes... nothing.

 

[gary courtney]

u like psting videos why not post the video of him screwing this bearing up. or did you get it mixed up with somebody elses videos. i built 2 660 using his videos as other people have. i did not c that. i need info I can count on.

This was not meant to bash anyone. I saw the video and posted what I did as a help to those who have heated the cases and the bearing not having anything to seat against.

 

[Slick50]

i built 2 660 using his videos as othe

gary was using and building saws before there was a youtube. Pretty pathetic you have to watch a video to build a saw.

 

[gary courtney]

i did, i forgot that video. i beat it in to far with that new tool i just got. i thought you meant i knocked it out. you can see in that video there was no lip on that race either. so the lesson is and i say so right on the screen STOP

This is Bedford T's video! So @ Tree Joe Are you saying you are Bedford T! Do you have 2 identities on here?