McCulloch Chain Saws

[j-jock]

Thats a good one to have
http://www.acresinternet.com/cscc.n...7a0c5cc22d71ae4188256c2e0077863e?OpenDocument

Oh! I'm so happy. I was hoping it was an SP81. Thanks. I have some pictures, but I have to shrink them before posting. We are forecast to get snow tonight, and I am in a panic, because this was the moment the starter solenoid on my ATV powered snowplow, decided to fail on me.
The plow, is a new experience for me, and I need it because I am getting a little old to risk hand shoveling snow on my long, steep driveway. It doesn't snow here often, but when it does, think two feet of wet, sloppy crud.
Bob

 

[Maintenance supervisor]

Oh! I'm so happy. I was hoping it was an SP81. Thanks. I have some pictures, but I have to shrink them before posting. We are forecast to get snow tonight, and I am in a panic, because this was the moment the starter solenoid on my ATV powered snowplow, decided to fail on me.
The plow, is a new experience for me, and I need it because I am getting a little old to risk hand shoveling snow on my long, steep driveway. It doesn't snow here often, but when it does, think two feet of wet, sloppy crud.
Bob

If its like the old ford post style solenoid, you can still get one at a local auto parts store .

 

[heimannm]

Using a smaller than "recommended" file will produce a chain that cuts faster, but will not hold an edge as long.

Conversely, using a larger file or the same size file all the way to the end of the tooth will produce an edge that lasts longer but won't cut quite as fast.

Mark

 

[PogoInTheWoods]

Regardless of file size, correct hand filing technique is required for a chain to cut anything except maybe the operator -- if hand filing of course. File jigs go a long way in keeping an acceptable cutting angle on the cutter when using a correct or smaller sized file. Using a smaller sized file without one usually results in less than desirable performance for an inexperienced hand filer.

Too large a file under any circumstances may be great at hogging out a poorly maintained gullet, but will result in cutter back slope and not much cutting action at all. Same goes for a grinding wheel toward the end of a cutter's usable life unless the operator grinds into the tie strap to get any type of decent angle on the cutter. ((You'd be amazed at how many guys with grinders actually do that exact thing instead of just switching to an 1/8" wheel.)

Then there are the rakers...

..., and lots of other threads on the subject.

Point is, too large a file may as well be a rock or piece of chain link fence when it comes to "sharpening" a chain.

Too small a file will result in a nice sharp hook with no support to maintain an edge that will dull very rapidly as a result.

Chain manufacturers recommend file and grinding sizes and specs for a reason. You're usually pretty safe following those if you're not already an experienced filer or grinder.

 

[Maintenance supervisor]

Regardless of file size, correct hand filing technique is required for a chain to cut anything except maybe the operator -- if hand filing of course. File jigs go a long way in keeping an acceptable cutting angle on the cutter when using a correct or smaller sized file. Using a smaller sized file without one usually results in less than desirable performance for an inexperienced hand filer.

Too large a file under any circumstances may be great at hogging out a poorly maintained gullet, but will result in cutter back slope and not much cutting action at all. Same goes for a grinding wheel toward the end of a cutter's usable life unless the operator grinds into the tie strap to get any type of decent angle on the cutter. ((You'd be amazed at how many guys with grinders actually do that exact thing instead of just switching to an 1/8" wheel.)

Then there are the rakers...

..., and lots of other threads on the subject.

Point is, too large a file may as well be a rock or piece of chain link fence when it comes to "sharpening" a chain.

Too small a file will result in a nice sharp hook with no support to maintain an edge that will dull very rapidly as a result.

Chain manufacturers recommend file and grinding sizes and specs for a reason. You're usually pretty safe following those if you're not already an experienced filer or grinder.

I use a 1/4" file on my .404 because I'm a bad person.

 

[vinnywv]

To take away anything from these posts....do what makes you comfortable and works for you.

 

[knightmax]

Final Inspection passed! MacHalla is ready for concrete, electric, insulation and shelves. Maybe heat too lol!

 

[Squareground3691]

Final Inspection passed! MacHalla is ready for concrete, electric, insulation and shelves. Maybe heat too lol!View attachment 1036172

That’s awesome

 

[PogoInTheWoods]

I use a 1/4" file on my .404 because I'm a bad person.

7/32" would make you a better person. LOL

 

[PogoInTheWoods]

do what makes you comfortable and works for you.

Running a dull chain backwards will work for somebody who doesn't know any better.

But if it makes them comfortable...

 

[Maintenance supervisor]

7/32" would make you a better person. LOL

I've played with alot of .404 at this point and some does have a better fit with 7/32nd file ,but most cutters will get a gullet shelf with that file . It's definitely not a one size fits all because the old stihl semi chisel .404 is definitely smaller than an Oregon semi chisel.

 

[heimannm]

I even have some 5/16" and 3/8" files for the big, old, two man saw chain. 1/4"?? several lifetimes supply.

Mark

 

[Syncop8r]

I decided to try to tune my 10-10 tonight...

OK, first thing is it's idling too high.... I'll just turn the idle screw until the chain stops moving.....

 

[Jethro 2t sniffer]

I decided to try to tune my 10-10 tonight...

OK, first thing is it's idling too high.... I'll just turn the idle screw until the chain stops moving.....

View attachment 1036292

Oh bum

 

[heimannm]

Just stretch the throttle rod until you achieve the desired results...or start opening the L until is slows down and hope it's not too much fuel at idle speeds.

Mark

 

[edju1958]

I hate carbs like that.Is there a hole in the side of the airbox where an idle screw might go?Possibly missing that screw?

 

[vinnywv]

Its also possible to adjust that idle by the screw thats on the trigger underneath. Mac actually used that as an idle adjustment on some models. Might be worth a shot until you can locate that idle screw and spring for the carb.

 

[flatsfisher]

speaking of the trigger lock screw (throttle latch assembly). I have them on my SP70 and 10-10. my 10-10S does not have one and there is no provision for one. is that common? they are very nice for starting a cold saw.

 

[vinnywv]

Not common for a 10-10s to not have a lock. Should be in the handle. Operator presence lever type.

 

[flatsfisher]

I'll be. It has the in-handle trigger safety that is depressed with your palm when you grip the rear handle, but I didn't know it was also a trigger lock/fast idle switch, if that's what you mean. I had that all apart for painting and didn't catch that. I'll look at it again tomorrow.