Nik's Poulan Thread

[a. palmer jr.]

Mine doesn't have a knob that you push forward, it has an arrow on it kinda like the adjustable oiler on saws that points clockwise. I may have to take the cover off it to see if anything's inside..If it isn't complete inside I have plenty of the 1/4" chain so I'll just change it.

 

[RedneckChainsawRepair]

Now yesterdays pick up 90cc 42mm stroke. Now that I could get into I think.

 

[drumbum]

Anybody know what husky/partner brake bands fit the 3450/3750 330/380 series.

Can't imagine why mine broke.

 

[Modifiedmark]

Mine has points Brandon. [emoji38]

Steve, Samsung On5 using Tapatalk

You should just get the whole thing from him, you could then convert it to electronic that way. Use the cyl, and the electronic coil that way. I don't remember if the flywheels were different or not but you would have that too if needed.

 

[s sidewall]

I may do that, trying to finish up my 5200 now, fixing my 34/3700 drained back my saw funds some.

Steve, Samsung On5 using Tapatalk

 

[RedneckChainsawRepair]

I'd fix the wizard up he offered and use the other one for parts for it. @s sidewall

 

[redunshee]

Mine has points Brandon. [emoji38]

Steve, Samsung On5 using Tapatalk

let me check. I have a P&C somewhere. Not sure if it's points or not. If it is u can have it.

 

[redunshee]

let me check. I have a P&C somewhere. Not sure if it's points or not. If it is u can have it.

Well, I'm not sure what I have. Pic attached.

 

[a. palmer jr.]

I'm glad I said it "appeared" to be complete. It appears now that the knob is missing that you push to sharpen the chain. It just has a plate with an L shape in it. The saw will run but I'm sure it needs a little carb cleaning/fuel lines/air filter like most trade-in saws. I have a parts saw with a new chain on it so I may do some parts swapping, maybe come up with one good saw. This will be a future project for when I don't have anything else to do..

 

[a. palmer jr.]

I've since acquired a Roper 3.7, also with their version of a self sharpening system...it has a conventional chain on it, guess they didn't like the self-sharpener or wore it out..these saws appear to be a bit harder to get parts for.

 

[redunshee]

Found cylinder but don't know if it's points or not. Pics attached

 

[s sidewall]

I may get part saw from Brandon, got to wait to get saw funds back up. Two rebuilds pulled it down.

Steve, Samsung On5 using Tapatalk

 

[redunshee]

I may get part saw from Brandon, got to wait to get saw funds back up. Two rebuilds pulled it down.

Steve, Samsung On5 using Tapatalk

Well if u need anything else let me know. I've got a basket case of S25da parts you can have. Didn't see a piston however.

 

[s sidewall]

Ok, thanks for the offer.

Steve, Samsung On5 using Tapatalk

 

[RedneckChainsawRepair]

All done now that the muffler parts came in to make it right the way I wanted on the other 2.

2 were bought for parts saws for my runner. But I just finished up the other 2 now as all the muffler parts were found that I wanted to make them right.
My 3 3 cube size saws I love to cut with 16" under. Poulan 335 predator saws without the chain brake.

 

[brandonstc6]

My craftsman 3.7 wouldn’t start and I turned it upside down and a-bunch wd-40 ran out. Is there anything I can do to get it un-flooded besides letting it sit upside down


Sent from my iPhone using Tapatalk

 

[PogoInTheWoods]

Pull the rope a lot with it upside down or blow it out with compressed air?

 

[s sidewall]

Pull spark plug, turn upside down with piston half way open.

Steve, Samsung On5 using Tapatalk

 

[redunshee]

That's how I do it. How did WD40 get in the cylinder? Did u use it to install the cylinder? I normally use my finger to spread a little 2stroke oil.

 

[brandonstc6]

That's how I do it. How did WD40 get in the cylinder? Did u use it to install the cylinder? I normally use my finger to spread a little 2stroke oil.

It was like that when I bought it, I got it from the junkyard


Sent from my iPhone using Tapatalk