Nik's Poulan Thread

[green lust]

It’s hard to believe that 2 years ago I asked a friend of mine if he knew where I could find a bow saw for cutting my firewood. This is just a few of what I’ve accumulated. Is there a pill for this condition?

 

[s sidewall]

It's called leave them on the trailer and I'll fix your problem. Nice bunch of saws.

Steve Sidwell

 

[Goinwheelin]

Poulan on a Saturday afternoon

 

[3000 FPS]

It’s hard to believe that 2 years ago I asked a friend of mine if he knew where I could find a bow saw for cutting my firewood. This is just a few of what I’ve accumulated. Is there a pill for this condition?
View attachment 800362

No pills just more saws.

 

[Todd Loosli]

Goin.. . If you want to make that saw look nicer polish the right side of the cylinder as in sand the flashing on the fins and buff it good

 

[s sidewall]

Wished I thought of that, would have looked real good.

Steve Sidwell

 

[Todd Loosli]

This is my 4200 it was ruff looking

 

[Goinwheelin]

I see. Kinda like they do on the Harleys.

 

[Screwbolts]

This is my 4200 it was ruff looking View attachment 800579

Yup you guys make them a real pretty polished fin saws. As for me, they will keep the flashing and textured surfaces that radiate heat more efficiently.

Wheelin, are you referring to all them Harlys one sees in the back of trucks or being carried on trailers?

 

[Goinwheelin]

No it’s just a reference to cylinder fin treatments on air cooled piston engines.

 

[Goinwheelin]

 

[s sidewall]

Wonder how it would look to have the whole cylinder polished

Steve Sidwell

 

[Maintenance supervisor]

These were the seals recommended on this forum for the 4200 I have. The original one is quite abit larger id than the new, the new ones fit but boy it was tight? Are you guys using the same ones?

 

[RedneckChainsawRepair]

Folks wanted to know the differences in 15 25 45 on the CRG. 48mm and 50mm OE no AI and NE air injection.

445 50mm quad is my favorite and runs right with the 505 54mm dual singles IMHO. Why all the 52mm 475's get sold off.

 

[Goinwheelin]

View attachment 800647
These were the seals recommended on this forum for the 4200 I have. The original one is quite abit larger id than the new, the new ones fit but boy it was tight? Are you guys using the same ones?

I hope so because I ordered the same part #

 

[s sidewall]

I ordered off jacks small engines and got the correct ones. I had the same problem with the crank being hard to turn, seal too tight. Install original Poulan seals and had no problem.

Steve Sidwell

 

[s sidewall]

SKF 6904 is what I got the first time, they were a no go.

Steve Sidwell
Poulan seal number-530019075

 

[s sidewall]

https://www.jackssmallengines.com/jacks-parts-lookup/part/poulan/530019075

Steve Sidwell

 

[Maintenance supervisor]

SKF 6904 is what I got the first time, they were a no go.

Steve Sidwell
Poulan seal number-530019075

Thanks,I didn't have a hard time turning the crank but I can't imagine that they will last very long being that tight .
I think I'll probably be tearing it down because I've got some travel in the crank from side to side and a strange gas leak from the bottom of the saw? I try Jack's.

 

[Maintenance supervisor]

I hope so because I ordered the same part #

Let me know what you think of them , its just alittle too close.