Nik's Poulan Thread

[Rakoprtr]

Ok so here's the question is there any in 24 or 22 inch either k041 or k095 that's a 325 or is that pretty much impossible to find I been googlefu-ing and can't find anything

 

[Modifiedmark]

That doesn't work too well on the 3300 and 3000 because the top of the oil slot is so thin.
Some bars work really well some not at all depending on how far you have to raise the slot!!!:msp_mad:


Mike

Hmm, maybe but I have not found one that wont work that way, Yet..........

Ok so here's the question is there any in 24 or 22 inch either k041 or k095 that's a 325 or is that pretty much impossible to find I been googlefu-ing and can't find anything

I thought you were joking so I looked to see where your from. :hmm3grin2orange: I suppose you have some pine trees around to use that setup on.

Oregon still list a small mount Husky K095 mount in 24 and 28" but you would have to change the tip to make it a .325 pitch.

I really think I would stop at a 20" on a 3300....

 

[Modifiedmark]

Find me a couple of those in 16"!!!


Mike

OK

16" OREGON PRO-LITE BAR #160GLGK041 FOR Jonsered poulan | eBay

I think this is the old 095 mount that will work as a A041 or a K095 mount. Wish they still made them.

Oregon chainsaw bar .050 .325 66d new remington poulan 095 mount 16" | eBay

ECHO HUSQVARNA JOHN DEERE JONSERED POULAN CHAINSAW 16" SAW BAR BOX82 | eBay

K095 mount but cheap.

Bailey's - Carlton 16" Timber Champ Unbranded Chainsaw Bar 66 Drive Links

 

[Rakoprtr]

Hmm, maybe but I have not found one that wont work that way, Yet..........



I thought you were joking so I looked to see where your from. :hmm3grin2orange: I suppose you have some pine trees around to use that setup on.

Oregon still list a small mount Husky K095 mount in 24 and 28" but you would have to change the tip to make it a .325 pitch.

I really think I would stop at a 20" on a 3300....

I have A pine tree that fell in one of my customers yards last winter been trying to get it cut and hauled out of his yard for a while now its 35 inches in diameter the power company had someone haul the top away as it fell over the lines and road but there's about twenty foot of the tree left And the rootball

 

[hemiyota]

National 471466

Picked up a few of these seals. They are almost twice the thickness of the original. Will the extra thickness matter? Will they still go in flush with the case?

 

[fossil]

Thank u rep sent and that's just my luck there expensive

Try Laser Sales. They have 16, 18 and 20" .325 .050 bars that fit a 3300 in their forestry pro bar. I bought one for my ECHO 6700 and it seems pretty well made. It's made in Germany and has a replaceble tip. The 20" is $47.85.
You can download their catalogue on line . They also have some Japanese Tsumara bars left in a few sizes and mounts but not for yours.

 

[Rakoprtr]

I guess 24 is a little big for a 54 cc maybe ill get lucky n my wife will let me get an 044 haha not

 

[promac850]

I guess 24 is a little big for a 54 cc maybe ill get lucky n my wife will let me get an 044 haha not

Meh, forget the 044... get a Mac PM700 or 7-10. I'm sure you'll like it more than the creamsickle.

 

[Modifiedmark]

Picked up a few of these seals. They are almost twice the thickness of the original. Will the extra thickness matter? Will they still go in flush with the case?

I have used them before and there close to the originals in my experiance. There only .25" wide....

 

[Rakoprtr]

Meh, forget the 044... get a Mac PM700 or 7-10. I'm sure you'll like it more than the creamsickle.

Like it more yea problem dinner to play with at the gtg yea prob better for working cutting firewood and finding parts for thats debatable although I have yet to run a Mac that big I guess only time (with a little help from my cad) will tell

 

[Rakoprtr]

View attachment 244334

Been lookin for anything around the 70 cc or bigger range to get thru this beast but right now everyone wants an arm and a leg for one and I find it harder to work with only one arm and one leg might be worth it tho

 

[hemiyota]

I have used them before and there close to the originals in my experiance. There only .25" wide....

Well, if you've actually used them, I guess they'll work. I was just wondering if the extra thickness would interfere with the oil pump or flywheel.. These aren't actually NATIONAL seals, but they're SKF seals, crossed over at NAPA.

 

[Modifiedmark]

Well, if you've actually used them, I guess they'll work. I was just wondering if the extra thickness would interfere with the oil pump or flywheel.. These aren't actually NATIONAL seals, but they're SKF seals, crossed over at NAPA.

I now see what your saying, and I dont remember there being that much difference between them. Your original seal looks thinner then what I remember them looking like.

You should be fine though, there should be enough room no problem.

Been awhile since I got any but I do have another 5200 project and will be getting some seals for it.

 

[3000 FPS]

Weld job on 3750

This is my before and after on a 3750 I was working on. Not my best work but it was in a very tight spot and since I am still learning in welding on magnesium it will work and I can say at least there will be no leaks.

View attachment 244373

 

[Islero]

Removing Rear Insolator Spring From Poulan Pro 4218 AVX

Good Afternoon,

Would someone be so kind as to tell me how to remove the rear insolator spring from the Poulan Pro 4218 AVX and where I can purchase a replacement spring? The part number is 530059475. Thank you, Islero :smile2:

 

[Rakoprtr]

Good Afternoon,

Would someone be so kind as to tell me how to remove the rear insolator spring from the Poulan Pro 4218 AVX and where I can purchase a replacement spring? The part number is 530059475. Thank you, Islero :smile2:

Post a pic of it i might have one

 

[Islero]

Post a pic of it i might have one

Rakoprtr, I do not own a camera nor a cell phone. However I do appreciate your response to my question. Thanks, Islero :smile2:

 

[RedneckChainsawRepair]

Rakoprtr, I do not own a camera nor a cell phone. However I do appreciate your response to my question. Thanks, Islero :smile2:

This might help. This? http://www.ereplacementparts.com/images/part_p_266772_724963612.gif

$6-7 new

 

[Islero]

This might help. This? http://www.ereplacementparts.com/images/part_p_266772_724963612.gif

$6-7 new

JeremiahJohnson, thanks for the link. Have been checking Ebay with no luck, Islero

 

[RedneckChainsawRepair]

JeremiahJohnson, thanks for the link. Have been checking Ebay with no luck, Islero

Your welcome. Little hint. Just put part number in Google search. You can find anything just about that way.

Also use part number in feebay search and you will turn a couple up too.