Sold NOS Oregon 29" Bars

[sross]

Can you buy an off the shelf chain to fit this size or have to make one? Do you have any chains to fit? Tks

 

[mikerudder]

93 DL is what I have been told.
could be different for different saws!
I have no chain made up for it unfortunately

 

[Bob95065]

I'm interested in one if there's any left

 

[tspeedle]

I’m also interested, would even take two or three

 

[mikerudder]

I have about 30 left!
Fire me a PM to work out the details

 

[Woodslasher]

You wouldn't have got an old, dark grey single rivet 3/8 Oregon bar tip in that bar lot, would you?

 

[mikerudder]

You wouldn't have got an old, dark grey single rivet 3/8 Oregon bar tip in that bar lot, would you?

3/8”
Is this what you are looking for?

 

[Woodslasher]

Close, but not quite. I'm looking for an oddball dark grey tip from the 80's, like so: I found that bar's nos little brother sans tip and I'd love to have a period-correct 3/8 tip for the bar.

 

[mikerudder]

Close, but not quite. I'm looking for an oddball dark grey tip from the 80's, like so: I found that bar's nos little brother sans tip and I'd love to have a period-correct 3/8 tip for the bar.
View attachment 955570View attachment 955571

3/8 or .404”? I’ll take a peak

 

[Woodslasher]

3/8 preferably, the bar is 0.050 and .404 x 0.050 is hard to find.

 

[Bill G]

93 DL is what I have been told.
could be different for different saws!
I have no chain made up for it unfortunately

93dl is not right as that would be close on a 3/8 bar but these are .404. I will look up the correct info in the Oregon book later

 

[mikerudder]

93dl is not right as that would be close on a 3/8 bar but these are .404. I will look up the correct info in the Oregon book later

I’m just going off what a buyer told me he put on.

 

[Modifiedmark]

I’m just going off what a buyer told me he put on.

Mike you should ask Bill to let you know what the Oregon book list that bar number for application.

I have the earlier and a bit later books so I don't have the listing for them, but I am certain those are Dolmar mount bars. Oregon D033 mount for the 133, 142 144, 152, 153 and 166 saws. Like cbfarmall said they can be adapted to the big Stihl saws by drilling some hole's.

With easy to make stud spacers they can be adapted to many older saws. I have used this mount on Partners and Poulans and will probably work on the older Homelites that use the big bar mount.

I have enough bars or I would be taking a few of these. If the shipping from Canada wasn't so high I probably would anyway.

 

[mikerudder]

Mike you should ask Bill to let you know what the Oregon book list that bar number for application.

I have the earlier and a bit later books so I don't have the listing for them, but I am certain those are Dolmar mount bars. Oregon D033 mount for the 133, 142 144, 152, 153 and 166 saws. Like cbfarmall said they can be adapted to the big Stihl saws by drilling some hole's.

With easy to make stud spacers they can be adapted to many older saws. I have used this mount on Partners and Poulans and will probably work on the older Homelites that use the big bar mount.

I have enough bars or I would be taking a few of these. If the shipping from Canada wasn't so high I probably would anyway.

Yes, I’ve been told they are the Dolmar mounts but I’ve had guys adapt them to other saws so far.
Adapters and a couple holes drilled for the oiler and could probably be adapted to most saws.

 

[Modifiedmark]

Yes, I’ve been told they are the Dolmar mounts but I’ve had guys adapt them to other saws so far.
Adapters and a couple holes drilled for the oiler and could probably be adapted to most saws.

Ok your original post is still listing them as Stihl mounts so there is that..

 

[mikerudder]

Ok your original post is still listing them as Stihl mounts so there is that..

That’s what they are labeled right on the covers when I got them.
They fit my 880 so that’s what I’m going off.

 

[Bill G]

Ok your original post is still listing them as Stihl mounts so there is that..

That’s what they are labeled right on the covers when I got them.
They fit my 880 so that’s what I’m going off.

Well I did some digging tonight and found some information but not as much as I had hoped. As for the bar mount the Oregon sleeve was labeled Stihl because that is what they were sold to fit. The number 23779 is the ID number that pre-dates the more recognized and more recent system of assigning a classification of the early 1980's of E031 for bars that fit large Stihl or D033 for the large Dolmars. It looks like the basic difference between those two is the E031 has the 2 oiler holes drilled straight through whereas the D033 has one drilled through and one half-blind.
Now back to the bars at hand. The 1979 Oregon book shows the 23779 as a 29" .404 bar for the large Stihl saws. It shows it as a special order only bar. As for chains Oregon generally lists the driver counts but in this case they did not for 23779 as it was a special order.. The 25" bar with a solid nose calls for 80 drivers. The same design sprocket nose bar as you have in 33" is #23310 and calls for 99 drivers.
Now here is a bit more information the #23779 and #23310 are listed as fitting Stihl E15,050,051,07,08, 09, 09S, S10, and E30. I am a bit confused at what they mean with 09 and 09S. I assumed it was a misprint and they meant 090 but the next listing has the 090. They have a separate listing for Stihl 070 and 090. Now as I mentioned earlier the #23310 is listed as a 33" bar fitting the Stihl E15,050,051,07,08, 09, 09S, S10, and E30. . It calls for 99 drives. They then list #26041 as a 33" for the 070/090 with one extra link.
So in summary I cannot shed anymore real information than what you already know. I had hoped I could. As for driver count if someone has used the bars with 93 drivers then obviously it should be right. I am just going off what Oregon lists. The same bar in 33" takes 99DL which is 79.99 inches. A 93DL chain would be 75.144 inches so for simple sakes lets say the 33" bar takes 80 inches of chain at 93Dl the 29" bar would only take just shy of 5 inches less. That seems odd. Last night I was going to post I figured about 88DL but I wanted to check the book. Since the book does not list a driver count it is trial and error. A 88 driver chain should be 71.10 inches or 8.70 inches less than what is listed for the 33" bar. That seems more in line but if someone is using 93dl so be it.

Bill

 

[Clyde85]

I am not certain but I believe the 09&09s is its own model. I sold a 08s to my brother in law last September. I believe it was 56cc.

 

[Modifiedmark]

Well I did some digging tonight and found some information but not as much as I had hoped. As for the bar mount the Oregon sleeve was labeled Stihl because that is what they were sold to fit. The number 23779 is the ID number that pre-dates the more recognized and more recent system of assigning a classification of the early 1980's of E031 for bars that fit large Stihl or D033 for the large Dolmars. It looks like the basic difference between those two is the E031 has the 2 oiler holes drilled straight through whereas the D033 has one drilled through and one half-blind.
Now back to the bars at hand. The 1979 Oregon book shows the 23779 as a 29" .404 bar for the large Stihl saws. It shows it as a special order only bar. As for chains Oregon generally lists the driver counts but in this case they did not for 23779 as it was a special order.. The 25" bar with a solid nose calls for 80 drivers. The same design sprocket nose bar as you have in 33" is #23310 and calls for 99 drivers.
Now here is a bit more information the #23779 and #23310 are listed as fitting Stihl E15,050,051,07,08, 09, 09S, S10, and E30. I am a bit confused at what they mean with 09 and 09S. I assumed it was a misprint and they meant 090 but the next listing has the 090. They have a separate listing for Stihl 070 and 090. Now as I mentioned earlier the #23310 is listed as a 33" bar fitting the Stihl E15,050,051,07,08, 09, 09S, S10, and E30. . It calls for 99 drives. They then list #26041 as a 33" for the 070/090 with one extra link.
So in summary I cannot shed anymore real information than what you already know. I had hoped I could. As for driver count if someone has used the bars with 93 drivers then obviously it should be right. I am just going off what Oregon lists. The same bar in 33" takes 99DL which is 79.99 inches. A 93DL chain would be 75.144 inches so for simple sakes lets say the 33" bar takes 80 inches of chain at 93Dl the 29" bar would only take just shy of 5 inches less. That seems odd. Last night I was going to post I figured about 88DL but I wanted to check the book. Since the book does not list a driver count it is trial and error. A 88 driver chain should be 71.10 inches or 8.70 inches less than what is listed for the 33" bar. That seems more in line but if someone is using 93dl so be it.

Bill

Interesting, that mount looks just like the D033's I have here.

 

[Bill G]

Interesting, that mount looks just like the D033's I have here.

I do not doubt it does but I simply posted the information that is contained in the book that lists that exact part number