Oklahoma,AR,MO,KS,TX GTG (Next GTG 08/27/2016 ) Fort Scott, KS

[workshop]

Now all I gotta do is stack.

Sent from my SM-N910V

I wish you would have said something, Steve. I would have helped.

 

[cobey]

That hackberry limb/half tree made more wood than I thought..

 

[cobey]

View attachment 444132 View attachment 444133

All this elm came from the one tree my dad knocked down


This is the last of that elm
I picked up the "Sanford and son" trailer
From dads last night

 

[cobey]

Probably four times this must wood on the ground up at dads
His killer cows hate me..... I half to watch my back

 

[lumberjackchef]

Neighbor down the road from my house is putting in a new fence so they been cleaning the old hedge limbs . he told me I better get up there and get as much as I could before he pushes it in a pile and burns it. Tarin and I went and got a trailer load so far. There is probably 10 more there of nice medium sized stuff!!

 

[sawnami]

I wish you would have said something, Steve. I would have helped.

I appreciate that Steve but I took my time and it wasn't too hard to get done.

Sent from my SM-N910V

 

[cobey]

I appreciate that Steve but I took my time and it wasn't too hard to get done.

Sent from my SM-N910V

Hey Steve, there was no fuel line in the tank of that d44 that I got in Springfield.
I put one on and it runs and pulls fuel intermittently....
May still need a diaphragm....

 

[workshop]

Hey Steve, there was no fuel line in the tank of that d44 that I got in Springfield.
I put one on and it runs and pulls fuel intermittently....
May still need a diaphragm....

I wonder if the tank vent is working properly.

 

[Hinerman]

Pouring down rain here right now. Split some pecan this afternoon. Grilled burgers for Sam and a few friends.

 

[sawnami]

Hey Steve, there was no fuel line in the tank of that d44 that I got in Springfield.
I put one on and it runs and pulls fuel intermittently....
May still need a diaphragm....

You don't happen to have a pressure tester to check crankcase seals do you? It works great to check out a carb with.

Sent from my SM-N910V

 

[cobey]

I wonder if the tank vent is working properly.

Ya the vent works

 

[cobey]

You don't happen to have a pressure tester to check crankcase seals do you? It works great to check out a carb with.

Sent from my SM-N910V

How do you pressure test a carb ????? Never heard of that

 

[sawnami]

Pressurize it through the fuel inlet until the needle pops off the seat. It should re-seat around 10 PSI and hold. Use a vacuum pump on the pulse port and pump it with the pump valve open and watch for the pressure to decrease as you pump it.

Sent from my SM-N910V

 

[SteveSS]

Hey Steve, just believe that you'll come across several chainsaw finds along the way. Maybe that'll make it better.

I'm browsing CL right now. Nothing to speak of yet, but the week is young.

 

[Homelite410]

Got the fuel pump out of mommas van....... Stamped made in USA Walbro.

 

[Hedgerow]

Best go on and replace it with the zama from O'Reilly's..

Lol..

 

[Hedgerow]

 

[Hedgerow]

Missing a bunch of saw nuts sitting with me by this fire.

 

[67L36Driver]

Best go on and replace it with the zama from O'Reilly's..

Lol..

Excepting the Zamas that come on the McCulloch 2014 types, my track record with them is spotty at best.

 

[Redhorse]

There is a mill near Neosho, MO, just off hwy 60. Did you know it was there?

That one is closer to Monet believe it is Ozark Stave co. bout 5 miles from me. White Oak only, parent company is near Cabool I think. They were giving away the ends and pieces they couldn't use for staves for a while when they started. But now they chip them, they are the #1 supplier to kingsford charcoal.


Sent from my iPhone using Tapatalk