Partner Chainsaw Thread

[nenicu]

For general inforation: a Husqvarna 55 brake band can be made to work in a Partner 500[5000] chain brake. The fixed end has to be modified a little. I used a aftermarket band so maybe a original will work better. Edit: this fix works on the newer plastic chain covers.

 

[leecopland]

For general inforation: a Husqvarna 55 brake band can be made to work in a Partner 500[5000] chain brake. The fixed end has to be modified a little. I used a aftermarket band so maybe a original will work better. Edit: this fix works on the newer plastic chain covers.

Pics or it didn't happen

 

[sawnami]

Took these out of shelf queen status and fueled and oiled them and fired them up.

Sent from my SM-T900 using Tapatalk

 

[Jeff Lary]

Wow very nice. I have been working on 2018 fire wood these last 2 days and running my 5000's. I see the larger saws and think boy I want a 7000 or p-100 but the 5000 tires me out enough as it is. Too old, too fat, too much snow ha ha .

 

[leecopland]

Bigger is not always Better!

 

[SS Sniper]

Bigger is not always Better!

No, but sometimes it helps!

 

[Jeff Lary]

I had to have a rotator cuff repair a few years back and they installed a couple screws just for good measure. That shoulder gets to burning sometimes specially when limbing above shoulder height. I cut a big ash yesterday and some of the top had main limbs 7-8 feet in the air after it was on the ground , I tell ya I was happy when i got done with it. Adds to the tree length pile nicely but I would not want to do that all day every day for sure.

 

[nenicu]

Pics

 

[Jeff Lary]

Not attempting to thread jump but I know no other way to ask. So here goes, I recently bought a Poulan Pro 225 from a fella in the Trading Post I would like to now buy a case for it. If anyone has one that fits the little saw and you want to sell it please pm me I may be interested. I am going into the Poulan thread and post the same message. Thanks for your time and I apologize for jumping into the middle of things Thanks again Jeff

 

[bulletpruf]

Anyone have a clue on the going rate for a Partner R11? Complete, decent condition, not running. Hard to establish value when you don't see any of these changing hands on eBay.

Thanks,

Scott

 

[sawnami]

Pulled the front one out of the box and did a group photo.

Sent from my SM-N910V

 

[Jeff Lary]

Nice looking

 

[fechtichmac]

Left one looks new ?[emoji50]

Gesendet von meinem SM-G928F mit Tapatalk

 

[sawnami]

Thanks. The left one is a new one.

Sent from my SM-T900 using Tapatalk

 

[rynosawr]

Hey gang,

I am searching for a good used ignition module/coil for a Partner P100 Super...

It was really running great after a fresh carb kit, fuel line, and cleaning it out with some sea foam to loosen the rings out a bit.... the piston and cylinder look great and it has awesome compression!

I ran it quite a while after the freshen up and went to start it the next day and she wouldn't even cough or sputter...

Tested spark and found it very, very weak... gapped module at .008 and no better spark.

Pulled spark plug wire out of module and found almost all the wires were broke off that were touching the module post... got it!

Wrong.... same weak spark as before...

Did the coil in the oven trick after that, still no good...


Can anyone help me out?

 

[fechtichmac]

Hey gang,

I am searching for a good used ignition module/coil for a Partner P100 Super...

It was really running great after a fresh carb kit, fuel line, and cleaning it out with some sea foam to loosen the rings out a bit.... the piston and cylinder look great and it has awesome compression!

I ran it quite a while after the freshen up and went to start it the next day and she wouldn't even cough or sputter...

Tested spark and found it very, very weak... gapped module at .008 and no better spark.

Pulled spark plug wire out of module and found almost all the wires were broke off that were touching the module post... got it!

Wrong.... same weak spark as before...

Did the coil in the oven trick after that, still no good...


Can anyone help me out?

One piece ignition or ignitron?

Gesendet von meinem SM-G928F mit Tapatalk

 

[rynosawr]

It says Ignitron on the recoil cover, which looks like a one piece to me if original to the saw.


I can take a pic later today

 

[fechtichmac]

It says Ignitron on the recoil cover, which looks like a one piece to me if original to the saw.


I can take a pic later today

If ignitron , there is a hidden "rifa" electronic module in the rear handle base located under the killswitch. Sometime wires not correct or grounded

Gesendet von meinem SM-G928F mit Tapatalk

 

[fechtichmac]

If ignitron , there is a hidden "rifa" electronic module in the rear handle base located under the killswitch. Sometime wires not correct or grounded

Gesendet von meinem SM-G928F mit Tapatalk

You can use a "real" one piece coil off later partners so as p7000plus or husqv.272 ... if so, rifa module has to be removed

Gesendet von meinem SM-G928F mit Tapatalk

 

[rynosawr]

If ignitron , there is a hidden "rifa" electronic module in the rear handle base located under the killswitch. Sometime wires not correct or grounded

Gesendet von meinem SM-G928F mit Tapatalk

Well, that is it!!

The wire had fallen apart to the module inside the handle! Geez, what a place to hide the module....

The wire was broken completely off the rifa module....

I bet with new wiring she will be back to a nice roar!