Pioneer chainsaws

[2stroke_shaman]

Hoggwood,
Thats a good lookin saw . Thanks for the scan of the spike . Looks like it might fit my 14/20. I'll fit it before drilling

 

[fossil]

Doing a little fab work on the 3200. I banged out a spark plug cover and made a spike from the scan Cory provided. Didn't put one scratch on the paint either.

 

[fossil]

Hoggwood,
Thats a good lookin saw . Thanks for the scan of the spike . Looks like it might fit my 14/20. I'll fit it before drilling






View attachment 611455


View attachment 611456

How did those saws do clearing noodles? It doesn't look like there was much room under the clutch cover.

 

[Walter Glover]

Is that sweet 3200 a runner? Have a bar for it yet? Gotta see some chips eh!

 

[fossil]

Is that sweet 3200 a runner? Have a bar for it yet? Gotta see some chips eh!

Sure is Walter. I can use a D096 bar with a spacer in front of the bar slot so I can tension the chain plus a couple of springs over the studs. Runs strong and it's very light for a 77cc saw. I have the 16" hard nose that came with it.

 

[Beavers]

Sure is Walter. I can use a D096 bar with a spacer in front of the bar slot so I can tension the chain plus a couple of springs over the studs. Runs strong and it's very light for a 77cc saw. I have the 16" hard nose that came with it.

Ear plugs and a good set of anti vibe gloves optional

 

[fossil]

Is that sweet 3200 a runner? Have a bar for it yet? Gotta see some chips eh!

I posted this up a few pages ago Walter. Next run I'll try an 8 pin rim and see how that goes.
I think the short sleve days are gone.

 

[Beavers]

l seen a earlier post on this subject. This is my removal tool for the seat removal. the snap on socket also works , you can grind down any other 5/16" socket as previously mention as well.

 

[chainmaster]

Picked these up Saturday morning P50/P42/41/40/
and two P28,s one Homelite 410

 

[Walter Glover]

Fix

 

[fossil]

View attachment 612583 Fix

Must be a very rare Pioneer. Looks just like a MAC

 

[2stroke_shaman]

The epoxy/ stud looks good . Well done!

 

[2stroke_shaman]

Doing a little fab work on the 3200. I banged out a spark plug cover and made a spike from the scan Cory provided. Didn't put one scratch on the paint either.

View attachment 612026 View attachment 612027 View attachment 612028

That girl is likin the love . Great work on the cover.

 

[2stroke_shaman]

l seen a earlier post on this subject. This is my removal tool for the seat removal. the snap on socket also works , you can grind down any other 5/16" socket as previously mention as well.

I love the info sharing on this site. All for one . We are keeping history alive.

 

[2stroke_shaman]

What did I do with that flywheel nut ? LOL not the flywheel I want to work on but duty calls.

What I want to learn is welding on these saws like the repair on the recoil fins . Tig ?

Tom

 

[fossil]

What did I do with that flywheel nut ? LOL not the flywheel I want to work on but duty calls.

View attachment 612729

What I want to learn is welding on these saws like the repair on the recoil fins . Tig ?

Tom

I sure would like a TIG welder to learn on. The flywheels are likely aluminum but I'm not so sure. So many diecast products are magnesium as it diecasts very well.

Rocketnorton would be a good guy to get in touch with regarding TIG stuff.

 

[Walter Glover]

Sorry for posting that yellow thing here!
My bad!

 

[fossil]

Sorry for posting that yellow thing here!
My bad!

Just kidding Walter. I can't throw stones in that area.

 

[2stroke_shaman]

Suck squeeze spark bang . All related .

 

[rocketnorton]

suck squeeze bang blow. how we were splained in school
tig: jugs & fw are alum. rest of saws is mag in most cases. some old sandcast stuff is alum. poulan & pioneer come to mind.
never welded on flywheels. if one fin was broke, id prolly just take one opposite it off.