I'm back
.Me either, probably some C4 in there to to help remove the evidence
.In Australia even the eyebrows are killer
.
Scrounging Firewood (and other stuff)
- Thread starter mainewoods
- Start date
Help Support Arborist Forum:
...
WoodAbuser
aka WoodchuckAbuser
Little something to cheer up you sad sacks.
Got a bit more done on the cherry Sunday.
Took a log off the main that a 24 wouldn't reach thru, wait, it was a stihl bar, so a 25.
Still a lot to do out there.
Took a log off the main that a 24 wouldn't reach thru, wait, it was a stihl bar, so a 25
.Still a lot to do out there.
Funny stuff for sure.
I won't be supporting or saying anything positive about that beer company after their woke messaging recently.
Get woke, go broke.
WoodAbuser
aka WoodchuckAbuser
I'm with you on that. I shouldn't wish bad on them, but it wouldn't hurt my feelings if all the woke corporations went belly up.
Got the last couple of scrounges split and stacked. I've kept the splits big because it is less dense wood than most of what I burn. Green density 1050kg/m, ADD 620kg/m compared to peppermint at ADD 820kg/m. Stihl, as @dancan would say, better than burning snowballs.
Sunday. That's candlebark down the bottom with the darker orange colour.
Today
Sunday. That's candlebark down the bottom with the darker orange colour.
Today
Jim estimates mid to late July for Edison to open Kaiser pass
Wellā¦except for the , uhā¦Buddie liteā¦
New topicā¦
those of you with 880 magnumsā¦what sort of muffler mods have you done? I have one on the bench for basic serviceā¦carb rebuild, etc. but figured Iād do a MM while itās here.
I tried searchā¦bustā¦tried YouTube, same
so, searching for a carb kit has been a bustā¦
Walbro WG12A
doesnāt even show up on the Walbro site, sheesh.
one possible on eBay but not exactly conclusive.
other sources?
those of you with 880 magnumsā¦what sort of muffler mods have you done? I have one on the bench for basic serviceā¦carb rebuild, etc. but figured Iād do a MM while itās here.
I tried searchā¦bustā¦tried YouTube, same
so, searching for a carb kit has been a bustā¦
Walbro WG12A
doesnāt even show up on the Walbro site, sheesh.
one possible on eBay but not exactly conclusive.
other sources?
Thanks for the 
Chipper butā¦not helpfulā¦
Chipper butā¦not helpfulā¦
Pa is a commonwealth. (Ie wealth of communism) .. we do everything arse backwards compared to real states.... we just keep the "key stone state" moniker for fun.
Well, the shops frame is at my place. 3 skids full of all sorts of 2x3" tubing and not a single scrap.of paper for what goes where and nothing that looks even close to being a man door frame. Sent the company an email. They've been pretty good about getting back to me about stuff so well see what they have to say.
Township called this morning to come pick up my permit. So looks likes everything is lining up. Just have to dig some footers and pour some concrete. Oh wait, I still need to finish moving the log pile.... yep. Need to kick it in gear now that the jetta is "done".
It got a new turbo, injectos, intake and exhaust this weekend. I installed the lift pump (got it used.) And like my luck. It was dead. Like dead as a door nail. That ticked me off pretty good, ordered a new one. Doesn't nessisarrily negatively affect the car, at least till it gets higher in the rpm and in higher gears. Now just need to data log while I'm driving and go back and forth with the tuner to get her dialed in. It's like a driving a new car. Actually has enough power to get out of its own way!
Township called this morning to come pick up my permit. So looks likes everything is lining up. Just have to dig some footers and pour some concrete. Oh wait, I still need to finish moving the log pile.... yep. Need to kick it in gear now that the jetta is "done".
It got a new turbo, injectos, intake and exhaust this weekend. I installed the lift pump (got it used.) And like my luck. It was dead. Like dead as a door nail. That ticked me off pretty good, ordered a new one. Doesn't nessisarrily negatively affect the car, at least till it gets higher in the rpm and in higher gears. Now just need to data log while I'm driving and go back and forth with the tuner to get her dialed in. It's like a driving a new car. Actually has enough power to get out of its own way!
How about adding a port on the front cover?New topicā¦
those of you with 880 magnumsā¦what sort of muffler mods have you done? I have one on the bench for basic serviceā¦carb rebuild, etc. but figured Iād do a MM while itās here.
I tried searchā¦bustā¦tried YouTube, same
so, searching for a carb kit has been a bustā¦
Walbro WG12A
doesnāt even show up on the Walbro site, sheesh.
one possible on eBay but not exactly conclusive.
other sources?
Like this...
Sierra_rider
Piss revver
I've never really been into that piss-flavored water anyway lol.
There's enough stihl bashing in here already, figured I'd leave this one aloneThanks for the
.What's the saw being used for. I prefer out the "passenger" side, except when I'm using a saw for flush cutting(I try to use my beat up saws for that) as it throws chips and dust up and you have to breathe more of the exhaust.
Personally I don't ever see myself using a saw that big, but if you send it out here I'll let you know for sure how I feel about it
.PS, can't believe you don't have more wood stacked up around there.
Will he still go in there now that he no longer owns the resort?
Would need to cut out the inner baffle for that but definitely a possibility
Used for cutting up big logs at the wood yard...that are too big for the processor.There's enough stihl bashing in here already, figured I'd leave this one alone
What's the saw being used for. I prefer out the "passenger" side, except when I'm using a saw for flush cutting(I try to use my beat up saws for that) as it throws chips and dust up and you have to breathe more of the exhaust.
Personally I don't ever see myself using a saw that big, but if you send it out here I'll let you know for sure how I feel about it
PS, can't believe you don't have more wood stacked up around there.
Saw is too clean inside to have been used much...bought in 2010.
Not likely. He's just estimating based on the last 25yrs. He's out of the business now...lives in Bishop.
I can remember 15-20' walls of snow at the pass in July but that was back in the early 80s.
Similar threads
Want to Sell
4 free saws
