Sure is quiet in here....do I need to start a fight?

[Cantdog]

Good Samaritan you.
Had an errand one bout crash into me over in Cali couple years back, rather big un close to 3 feet across, 4 big whirley motor rig with 4 blades on each motor, span of about 8" each set. Was adjacent to a park where some retailers were showing off the goods, seen it coming and sidestepped a couple steps, went whizzing by and smacked into a eucalyptus, plastic bits went flying. Operator showed up all outa breath, seen his rig and began whining bout the cost. Good thing it didn`t hit anyone, cost be much greater.

Yep though it was undamaged...….without the control was useless.....so my minute to shine...LOL!!!

 

[Cantdog]

Social distancing remember

Oh yeah….left it outside on the well curb an just pointed to it when he arrived.....pretty distant....me...

 

[pioneerguy600]

Oh yeah….left it outside on the well curb an just pointed to it when he arrived.....pretty distant....me...

Yep, very important, that.

 

[Jimmy in NC]

Little MS201T showed up recently.. had a recent carb swap but still ran poorly and hard starting. I played around fixing a multitude of small issues. Checked compression and while low I thought it was enough at 138. Finally today I popped the muffler off. Well.. the carburetor and all the fighting was trying to tune through a scored P&C. 4 for 4 being junk when I investigated. I bet I fix this and the 200T for him and the MS440 and BR600 are junked.

Yes getting a digital camera to focus down through the access hole is a trick.. I'll get better pics when its apart further.

 

[pioneerguy600]

That piston is toast, can`t say bout the cylinder til its off.

 

[Cantdog]

Hmmmmm....I thought that was the Stihls always looked.....funny....every one that has evah come to my shop looked just about like that....all this time I thought it was normal......learn sumpin' new every day.....

 

[dancan]

Stihl cut wood , no Huskakarona saws were harmed or even seen .

 

[pioneerguy600]

Can`t see the wind in the pics, was gusting quite strong during that job.

 

[pioneerguy600]

Load up some saws and go cut up some oak.

 

[dancan]

What a dog , would'nt cut , wouldn't run , wouldn't idle , what a dog ....

 

[Cantdog]

What a dog , would'nt cut , wouldn't run , wouldn't idle , what a dog ....

I thought it was a mouse anyway.....

 

[pioneerguy600]

What a dog , would'nt cut , wouldn't run , wouldn't idle , what a dog ....

Hey! That`s my ,MOUSE, you won`t find another like it.

 

[dancan]

I have a couple that are close Lol

 

[pioneerguy600]

I have a couple that are close Lol

But yours won`t start first pull, no matter how long it sits or how cold it is that saw starts first pull. It will idle in any position, any position, until it runs out of fuel.

 

[pioneerguy600]

I just noticed, its sitting on a ,Ford, tail gate, its doomed!

 

[Cantdog]

So.......I was going through some stuffs today and found an old friend I hadn't thought of in years......I wore this knife for 20 or more years.....every day...every day...

 

[pioneerguy600]

Funny and strange how we find things like that. I lost more of them than I ever kept but still have one main knife I had since the 60`s.

 

[pioneerguy600]

Was an uneventful day, nice and sunny but too cold for a walk on the beach.

 

[stihl023/5]

Was an uneventful day, nice and sunny but too cold for a walk on the beach.

Same here

 

[pioneerguy600]

Same here

We have snow storm approaching, be here tomorrow morning.