Swap meet...

[caddguy]

5 point dawgs and 3/4 wrap handle for an 044?

I am looking for some 5 pointers for my 044 and a 3/4 wrap handle

 

[terry2tmd]

Stuff to Trade

I got a running PM610 good torque nice runner could use a new pull rope al though I have this one working pretty good. I also have a poulan 2406 avh it is perfect drive sprocket and clutch are a little worn, but fires and runs so well it's boreing. Now for parts I have two full 2100 husky engine blocks one has the end of the crank shaft buggered up due to a hill billy flywheel removal, it was running before the incident perhaps a somple rethread will fix it. The other case is perfect I stopped using it because I have two other 2100 huskys running and I lost the oil pump. Nether saw has a working oil pump or clutch, but I know for fact they have perfect ignitions, and flywheels. I also have a working cylinder,crankcaes, and oil pump for a 051 the end of the crank is fubar, good piston,rings,cylinder,and crankcase.
I need the plastic throttle link in a 2100 husky, and a good oilpump complete with brass or bronze drive gear. I also need a working stihl 051AV coil, woul be interested in convertion kit to take it out to 076. I also need a full wrap front handle for a husky 2100.

 

[jockeydeuce]

Power Mac 6 muffler

Hey guys. Anyone got a complete muffler for a little Power Mac 6???

My Dad has one that runs good, but he lost the muffler somewhere. I've got tons of Stihl and Husky bits to trade or cash.

 

[Kwdog75]

Going to need a bar and chain for my Stihl 034 project, wanted a stihl bar but I would consider something else if it looks good.

 

[Modifiedmark]

Anyone got a crankcase locating dowel for a Husqvarna 1100? One of mine seems to have disappeared I suppose there the same on a 480, 2100 etc?

I could also use a set of bar studs and possibly a clutch cover for a 1100.

Let me know if you have anything and what we need to deal.


terry2tmd, I have new pawls ordered for my flywheel already but if they don't come in, I'll contact you on that 2100 flywheel as that's whats on my 1100.

 

[logging22]

I need a good clutch cover for an 026/whatever else fits an 026.

wiggs, i got your cover. Yours for a pm address.

 

[pinemartin]

Looking for a small running stihl saw (017/018/024/026). Have a homelite C5 in good condition for trade + ???

 

[pwoller]

Jonsered 621

Looking for a recoil, filter, top cover, and ignitor coil.

 

[wigglesworth]

wiggs, i got your cover. Yours for a pm address.

PM sent...

 

[terry2tmd]

Anyone got a crankcase locating dowel for a Husqvarna 1100? One of mine seems to have disappeared I suppose there the same on a 480, 2100 etc?

I could also use a set of bar studs and possibly a clutch cover for a 1100.

Let me know if you have anything and what we need to deal.


terry2tmd, I have new pawls ordered for my flywheel already but if they don't come in, I'll contact you on that 2100 flywheel as that's whats on my 1100.

Sounds good I got a runner!

 

[terry2tmd]

i have parts for some old huskys:greenchainsaw:

WOW! I could happily live in the back of that truck, got any old 2100, 2110,or 298 carcases?

 

[parrisw]

i have parts for some old huskys:greenchainsaw:

Get anywhere with that stuff?

 

[Kupreanof]

Cheapie tach?

Anybody got a cheapie tach that needs a new loving home? I want to put one on a milling saw and I don't have a credit card.

 

[roncoinc]

Homelite parts needed

Have a VI944 and need complete flywheel with starter pawls on it.
have a wild thing in parts,a mac 610 parts,028 muffler,some junk

 

[StihlGuitar]

Parts for sale or trade....


Still need Echo CS510 piston and cylinder

I've got a cs520 with good cylinder, tried rebuilding it a few years ago before I knew anything about saws and didn't acid wash the cylinder so new oem piston is mildly scored, saw ran but not well. PM me. interested in your 288 also.

 

[StihlGuitar]

064 Bearing

Looking for Bearings for 064. Actually just one but I don't remember which side, I think Flywheel. Also piston for Solo 603 and Stihl 075.

 

[epicklein22]

Looking for Bearings for 064. Actually just one but I don't remember which side, I think Flywheel. Also piston for Solo 603 and Stihl 075.

Flywheel side is generic, should be about to match one up at a bearing shop cheap.

 

[epicklein22]

I got a few saws up for trade or whatever. I need to pay my tuition for the spring semester next week.

372xp- new seals all the way around, new bearings, new top cover, new tilly carb, new 20" windsor bar, new top handle, new aftermarket dawgs and a nice used topend with 2 rings. This is one nice saw and runs strong.

2065 with 372 top end and new meteor piston. New air filter, 20" windsor bar. Runs nice, looks pretty good besides a crack in the top cover and a few nicks in the gas tank.

 

[stinkbait]

Still looking for an IEL Pioneer RA top cover. I know that they are a rare find. I don't care if its missing all the paint and embems. Hell, I don't even care if it's cracked. I just need a top cover bad. I have a good running RA and no top cover.

 

[Jacob J.]

Still looking for an IEL Pioneer RA top cover. I know that they are a rare find. I don't care if its missing all the paint and embems. Hell, I don't even care if it's cracked. I just need a top cover bad. I have a good running RA and no top cover.

I almost had to sell my soul to get one.