Swap meet...

[blsnelling]

I'm looking for a late model 066/MS660 crankshaft. This is to go in the saw donated and being raffled off to support Jasha. Please PM me if you have one.

 

[RedneckChainsawRepair]

I would like to find a 3750 poulan, I have all kinds of stuff to trade I also have cash.

Depends on the condition you are wanting

 

[fastLeo151]

Depends on the condition you are wanting

Preferably running, but I'm not against a project. What are the details?

 

[Scooterbum]

I'm looking for a late model 066/MS660 crankshaft. This is to go in the saw donated and being raffled off to support Jasha. Please PM me if you have one.

I've got a 660 crankcase somewhere around here, I'll have to see what shape the crank is in. Is this for the Jasha saw?

 

[RedneckChainsawRepair]

Preferably running, but I'm not against a project. What are the details?

This one is a tim allen edition 3750 not a regular black cover 3750. She is so ugly

She runs but could use a new piston kit IMO new ring on piston but scored up pulling 130psi. I loaned it out after rebuilding it and idiot didnt know what was going on when the impulse line came off and he started running it on half choke. Lesson learned.

I've Split crankcase in past due to crankcase seal leaking and all good down there bearing and seals etc.

 

[fastLeo151]

Sounds good email sent!

 

[hoeyrd2110]

alrighty well list of what i need:

-poulan 3000(3.3 is ok) cylinder or p/c
-poulan 3700 p/c
-echo 452vl coil

i would be willing to trade any of those three away for things for the other or if something peaks my interested
to trade away i got

-XL-12
-DB sears direct drive
-MacCat (mint just needs carb rebuild and lines)w/case
-Homelite 240(stripped spark plug hole)
-Poulan 3400cv

i'm looking for a bigger saw something 70cc+ like a few saws for one deal. but open to anything!

 

[jbird77]

saws

I have a jonsered 70 e lol with ignition probs , and i have a I-51 McCulloch with a 24 inch bar i think

 

[PogoInTheWoods]

I have a jonsered 70 e lol with ignition probs , and i have a I-51 McCulloch with a 24 inch bar i think

Whaddya want for em?

 

[350jeepcj5]

Need some parts,

I need the wrap part of a top handle cs3000, also need a 12" bar and chain, and bar nuts for it.

I need a carb kit for a eager beaver 2.0 rb-19 is the kit number.\

THANKS!

 

[Wagnerwerks]

Need some parts,

I need the wrap part of a top handle cs3000, also need a 12" bar and chain, and bar nuts for it.

I need a carb kit for a eager beaver 2.0 rb-19 is the kit number.\

THANKS!

I have a cs 3400 handle assembly on ebay right now. If that works on a 3000, I could make a better deal off eBay or I'm up for trades depending on what ya got.

http://www.ebay.com/itm/221137647962?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1586.l2649

 

[komatsuvarna]

Looking for a fuel tank and carb/airfilter mount base for a 394xp. Would also be interested in 394-395 parts saws. $$$$$ to trade.

 

[Warped5]

Looking for a Mac 10-10 or PM800 parts carcass ... have dead presidents or a one-eyed goat to trade.

 

[Mastermind]

Looking for a fuel tank and carb/airfilter mount base for a 394xp. Would also be interested in 394-395 parts saws. $$$$$ to trade.

I have a 394 that I've robbed a few bits from that I could let go of......

 

[komatsuvarna]

I have a 394 that I've robbed a few bits from that I could let go of......

Well I tell ya what I got Randy. Im trying to gather parts to build a 394-395 stock appearing play saw. I got a good 394 bottom, and a nice 395 topend.....but thats about it .....so I pretty much need about everything else . I have a few other parts, but not much. Figured a parts saw would be easier and cheaper than trying to buy all the parts separate. Ill give ya a call this week!

 

[mdavlee]

If you two get bored with the 394/5 stuff send it my way. I need a big saw for some wood laying on the ground this winter.:msp_biggrin:

 

[srcarr52]

I'll always take 394/5 parts if someone is looking to get rid of them. :msp_wink:

 

[Jacob J.]

Well, I'm looking for a new model of saw to play with and that model is: McCulloch Titan 70. If any of guys have one you want to trade or sell, or know of one, hit me up.

 

[cambl]

Skil 1645 and 1631

I still have these two sitting in my garage if anyone is interesed in a trade. See classifieds for details and pics.

 

[Duke Thieroff]

I have a Nice 288 I'd trade off, or a 371, neither are really beauty queens, but both run well and are in sound mechanical shape....

The 288 has a parts saw with it with a serviceable cylinder...


Looking for something interesting along the same lines and displacement, brands are no matter.

I don't want your 3 wild thing projects and a Homelite 240, or whatever.


Drop a PM.
Duke