Swap meet...

[hdtoolmkr]

Need a rear handle/fuel tank for 064, top cover for same as well.

 

[Duke Thieroff]

So here's the deal....I just sold this saw on eBay, and somehow it got damaged in shipping. Apparently where the rear handle meets the footpad got chunked out. This was the all metal tank design. So I will be refunding the buyer his money and receiving the saw back. This is a shame because this is a really sweet example of an 028. I could go a few ways with this, so I will...

-If you have a replacement tank you would be willing to trade/sell me we can work it out.

-If you happen to have the metal tank and you want a saw to mount it on I'm sure we could work out a trade, or what not.

-If you want to repair it.

I'm interested in offers, keep in mind I have yet to see the damage, but if it is only what is what was described it should be a simple fix.....Drop me a PM..


Here's the orginal eBay listing.....

For sale is a Stihl 028 WoodBoss. This saw is in overall good shape and does not have any major flaws such as crack or breaks. This sasw does, however have some small scuffs froms light usage. The decals on the cylinder cover and clutch cover are intact but are starting to lift. There is some paint missing from the underside of the saw as pictured. There is some carbon discoloring on the crankcase in the muffler area.

The Link To The Video Can Be Seen Here

Stihl 028 WB - YouTube

I have replaced a few wear parts on this saw, the new parts include:

-New Fuel Line

-New Ground Wire

-New Crankcase Impulse Line

-New Fuel Tank Vent Line

I have converted this saw over from the points ignition to electronic ignition using OEM Stihl parts. As a result this saw now has a reliable and maintenance free ignition system.

The crankshaft bearings are tight, with no play.

The AV buffers are solid and tight.

The drive sprocket shows some light wear.

This saw has the cast magnesium gas tank as opposed to the plastic one.

The chain has been hand sharpened and the rakers have been checked and set.

The chain is Stihl branded and has in excess of 75% of the life left in it. The 18" bar is also Stihl branded and has had the groove cleaned as well as the rails dressed.

The piston shows signs of very minimal use, the orginal machining on the piston can be clearly seen.

The carburetor may need some minor adjustment upon your receipt of the saw, as is common with environmental changes and small engines.

This saw has been disassembled and cleaned. You will not be receiving a filthy piece of equipment.

This saw is ready to be used and put to work.



Here's some pics...

Bump

 

[Modifiedmark]

Also looking for a clean Poulan 305/3000.

Dang, that didnt take long!

 

[cambl]

Tilli HS carb

Looking for a Tillotson HS218A or HS225A for Jonsered 630, with a fairly good throttle shaft. Have a few misc 920 and 670 parts to trade.

Thanks.

 

[jockeydeuce]

Looking for a Tillotson HS218A or HS225A for Jonsered 630, with a fairly good throttle shaft. Have a few misc 920 and 670 parts to trade.

Thanks.

That must be a typo...An HS218 is for a Stihl 045 or 056

 

[cambl]

That must be a typo...An HS218 is for a Stihl 045 or 056

Stihl may have used a HS218(B, C ?) but the Jonsered did use a HS218A.

 

[young]

anybody have any 3/8 tsumura 4 rivet tips? and 404 3 rivet tips?

got tons of bars, chain and some parts for trade.

 

[jakew88]

Got two 394 xp's. I would like to trade one for a smaller saw. I do not need two big saws. I took one in trade for some firewood and the other I bought off Craigslist and done some repairs. Have another thread on it. Both saws run great.

Would like to trade for a 346xp ideally. Straight up. If you got something similar like a 345 we can work something out.

Thinking power head for power head so shipping is easier? Never done this before


View attachment 258969
View attachment 258970
View attachment 258971
View attachment 258972
View attachment 258973

 

[jakew88]

View attachment 258974
View attachment 258976
View attachment 258977
View attachment 258978

 

[dragrcr]

I have a homelite 1050 auto I need to get rid of, I haven't had time to tinker with it but it starts when primed comes with a 32" bar (iirc) let's say $175 shipped in the states.
I also have a locked up but complete David Bradley for $50 plus shipping. Pm me email addy for pics...,

 

[Wagnerwerks]

Pioneer stuff

Anyone with a full wrap loop for a p40? I have tons of stuff to trade.

 

[Mastermind]

anybody have any 3/8 tsumura 4 rivet tips? and 404 3 rivet tips?

got tons of bars, chain and some parts for trade.

Tons huh? Really??????

Pics???????? :msp_sneaky:

 

[jockeydeuce]

Stihl may have used a HS218(B, C ?) but the Jonsered did use a HS218A.

Learn something new every day.

 

[young]

Tons huh? Really??????

Pics???????? :msp_sneaky:

ok ok not tons. so sue me.

 

[Wagnerwerks]

Wow

​

ok ok not tons. so sue me.

Gotta say... You backed that up.

 

[o8f150]

ok ok not tons. so sue me.

i will trade you a pile of poulan/echo bars for that pile:msp_biggrin::msp_biggrin:

 

[nstueve]

Looking for a stihl 046 jug. Got cash and parts to trade! PM me if you have a good jug!

 

[Mastermind]

ok ok not tons. so sue me.

My attorney will be in touch.

You got any small mount Husky bars in the pile????? We may be able to settle this out of court. :msp_wink:

 

[Chris J.]

Randy, I'm guessing that Young didn't get your permission to use the photo of your legs in his avatar.

 

[ChainsawmanXX]

! PM me if you have a good jug!

My girlfriend has two? Not sure if sjes willing to part with either of them, but ill check.

Looking for 350 husky gas line, and oiler gear.

Sent from my LS670 using Tapatalk 2