Swap meet...

[huskydude]

Need a few more MAC 3200 series parts.....

-Full trigger set up with rod or cable for carb
-Yellow plastic choke lever
-some extra hardware(torx/flathead screws from entire saw)

wish you had told me when i was sending the coil. all that junk is in my cellar trash can underneath beer cans and oil impregnated saw dust

 

[Jacob J.]

Did you get this yet? I have an 1123 mystery box which is certain to have at least 3 in it.

I'll swap for a good 3120 cylinder.... LOL. PM me addy if you still need it.

If you need a 3120 cylinder Tim, I have one here that may be usable.

 

[Overtrained]

wish you had told me when i was sending the coil. all that junk is in my cellar trash can underneath beer cans and oil impregnated saw dust

Haha leave it there. I was hunting saw parts down before the saw i was planning to fix even arrived. I got something else locked up, dont wry about it.

 

[Arrowhead]

The 021 flywheel has been taken care off. Thanks for all the offers Guys. :msp_thumbsup:

Now... where's all the 441 starter and clutch covers???? LOL

 

[arborealbuffoon]

Power sharp conversion kit!

Yes, it's true. I have an actual NOS Oregon Power Sharp conversion kit. Comes with a drive rim, a piece of rope to jam the jug and remove the clutch, the sharpener part AND a bar and chain. Not sure, but looks like a 20 inch bar to me. Must go.

 

[67L36Driver]

Need a few more MAC 3200 series parts.....

-Full trigger set up with rod or cable for carb
-Yellow plastic choke lever
-some extra hardware(torx/flathead screws from entire saw)

I'll look and see where I dumped the misc. from that 3200 I sent and get back to you.


Didn't think you'd need it.:msp_ohmy:

Carl.

 

[psuiewalsh]

I have an Echo 330EVL complete with an almost new sthil chain, cuts good but is cold natured. Looking for an 026 with good bearings.

Also looking for an 041 clutch cover with chain brake. Have some saws, parts, chains and cash to trade.

 

[Modifiedmark]

The 021 flywheel has been taken care off. Thanks for all the offers Guys. :msp_thumbsup:

Now... where's all the 441 starter and clutch covers???? LOL

Ed, I got a 441 in pieces in a box right now. The owner probably won't let me give them away though. Maybe you could borrow them till I get his piston and cylinder in ?:msp_wink:

 

[Arrowhead]

Ed, I got a 441 in pieces in a box right now. The owner probably won't let me give them away though. Maybe you could borrow them till I get his piston and cylinder in ?:msp_wink:

Thanks for the offer Mark. I'll pass though, I hate to borrow parts, the starter covers seem to be like hens teeth.... (used at least). My luck, I'll break it then need two of them.

 

[Warped5]

Good morning ... in need of 1 - 2 Mac 10-10 non-chainbrake clutch covers, please. Have stuff and moldy money to trade. Thanks!

 

[Arrowhead]

Anybody have any real good looking 18" or 20" Stihl branded bars. 3/8 would be great on the 20 and .325 on the 18, but it don't really matter. Any gauge.
Got trading stuff.

 

[Arrowhead]

Good morning ... in need of 1 - 2 Mac 10-10 non-chainbrake clutch covers, please. Have stuff and moldy money to trade. Thanks!

Morning Teddy! I'll check, but I think all mine are brake covers. I used the bag of screws from ya the other day.... worked great!! Thanks.

 

[Overtrained]

I'll look and see where I dumped the misc. from that 3200 I sent and get back to you.


Didn't think you'd need it.:msp_ohmy:

Carl.

Got the case and everything else from 08F150, just had a few missing things on it. Had you guys both send the parts out at the same time, I didnt know either. Not a big deal.

 

[Warped5]

Morning Teddy! I'll check, but I think all mine are brake covers. I used the bag of screws from ya the other day.... worked great!! Thanks.

Mornin' Ed! I started into my PM800 project Monday night and took inventory of my parts ... thanks to you they're all there! But I discovered I'll probably need to re-ring it at the very least ... so while the PM800 is shelved for the time being, I've got something else that's big and yeller to work on; but it's not a Mac!

 

[67L36Driver]

I'll look and see where I dumped the misc. from that 3200 I sent and get back to you.


Didn't think you'd need it.:msp_ohmy:

Carl.

Found that stuff.

How about a recoil or two, the carb. box cover and a muffler (maybe two)? Used spark plugs..........................

I still have your address.

Carl.

 

[Overtrained]

Found that stuff.

How about a recoil or two, the carb. box cover and a muffler (maybe two)? Used spark plugs..........................


I still have your address.

Carl.

Used spark plugs? Haha....do you have the trigger, safety lever, spring and carb linkage?

 

[nstueve]

Echo parts:
looking for a cs5100 P&C...

IS anyone making AM parts for these saws yet? anyone want to clue me in on where to go for echo parts?

Anybody have any real good looking 18" or 20" Stihl branded bars. 3/8 would be great on the 20 and .325 on the 18, but it don't really matter. Any gauge.
Got trading stuff.

mine all look like junk or I'd have one on it's way...

 

[turbo885]

Need a few more MAC 3200 series parts.....

-Full trigger set up with rod or cable for carb
-Yellow plastic choke lever
-some extra hardware(torx/flathead screws from entire saw)

is 365 the same by any chance BILL

 

[67L36Driver]

Used spark plugs? Haha....do you have the trigger, safety lever, spring and carb linkage?

Yup.

Looking for a padded envelope.............................................................


Carl.

 

[Overtrained]

Yup.

Looking for a padded envelope.............................................................


Carl.

Sent you back 2 pm's