Swap meet...

[Modifiedmark]

i have 17 different sprockets for mac,poulan,homelite,1 even says partner on the box, all are not marked& none say which saw they go to. if you need 1 & can get me the oregon # these need to go.(cleaning basement)

PM me the part # for the Partner and Poulans and I'll see what they go to. I may use them.

 

[FELLNORTH]

I have a john deere cs 46 runs good, extra mild port work, squish set at .022", 195 psi of compression, 18" john deere ( gb ) bar and oregon chain sharpened once. This saw has maybe 10 tanks of gas through it.

Looking to trade for a decent big ( 60 CC + ) stihl or husky progect saw
or long bar 32" + for husky d009 mount with chain

 

[squish9173]

sprockets

PM me the part # for the Partner and Poulans and I'll see what they go to. I may use them.

all sprockets are oregon,poulan-#28717,27930,28004(2),partner-24139.these i believe are new,do have a few surface rust spots.

 

[weimedog]

Anyone have interest in Poulans? The old die cast (metal ones?) I ended up with a 80_..something and a 3400. Both seem to have good compression but are missing bits and pieces. The 3400 missing the air filter & cover, the older one a muffler. I don't collect Poulans...only J-reds and Homelites. Will swap for similar parts saws. (Assuming interest and when I untangle from the last months worth of snow related disasters....coming up for air next week!)

 

[Modifiedmark]

Anyone have interest in Poulans? The old die cast (metal ones?) I ended up with a 80_..something and a 3400. Both seem to have good compression but are missing bits and pieces. The 3400 missing the air filter & cover, the older one a muffler. I don't collect Poulans...only J-reds and Homelites. Will swap for similar parts saws. (Assuming interest and when I untangle from the last months worth of snow related disasters....coming up for air next week!)

Let me see what I got laying around in red. I may have something for you. I don't really collect red saws, just a token one here and there.

Need more info on the saws though.

 

[Meadow Beaver]

I've got 2 and have no use for them.

I need an on-off switch from a late model Jonsered. It's a 2171, but others use the same switch, even pole pruners and weedwackers. Trade?

Jimbo

Really? I couldn't find any anywhere.

 

[Harzack223]

064

I hate to do this but money is tight and I need my truck more than this saw. I have a stihl 064 that was recently overhauled by Brad Snelling a few months ago. The saw doesn't look the greatest but anything that was worn or damaged was replaced. I am looking for best offer on this saw. I will get a picture up later tonight.

I might even get rid of my husky 266se, doesn't look the best but runs very well.

 

[computeruser]

Willing to trade cash for a running tail-handle reed valve Echo 300/3000/340/3400-series or similar. Doesn't need to be pretty, but it needs to work properly. I don't want the more popular top-handle version, since it's for dad to use on brush, pruning, and to cut stuff small enough to put in his brown yard waste bags, and if I give him a top-handle saw he will use it one-handed and hurt himself...

 

[jimbo1490]

I just got hold of a Pioneer P42 HP in fair condition that might make a good project. It has good compression, starts pretty easily and runs strong, though could certainly use a bit of clean up and tuning. The rear handle has a weld repair. There is a wear hole in the clutch cover. Clutch looks and works OK. Air filter missing, though the cover is present. A piece of foam has been substituted for the air filter, so at least there was some kind of filtration. It is missing one bar stud. $40 plus shipping, or what have you to trade? I need a Stihl big pattern bar, 36", pref .063 gauge, pref. 3/8 sprocket nose. PM me

Jimbo

 

[Arrowhead]

PM sent.

 

[Donley]

ANYONE HAVE AN 041 CLUTCH THEY'D WANNA PART WITH?

just send me a pm.

 

[Donley]

i also need some random parts for a husky 55. or pm me with what you have or if you need a husky 55.

 

[zr900]

I have a Stihl .404 138 drive link semi-chisel chain in excellent shape.

Its full comp RM or RMC They have the blued cutter.

Would like to trade for a couple loops of 3/8 .050 72 or 84 Drive liknk chains

PM me if you got something to trade

 

[syde2side]

I've got an old xl12 that is complete and an xl10 that is 70% there. xl12 sorta runs, just needs a little tlc. they were both drug out of an old saw shop here locally that was going out of business. $25 would take them both home. xl12 does have an old bar and chain on it. could definetely use a new b/c.

 

[little possum]

Does anybody have a good 262xp tank theyd like to do some swappin on?

Thanks

 

[terry2tmd]

I Might know where I can get my hands on a 262 tank, I'll have to check, and I'll PM you and let you know. Hey anybody know what the point and plug gap for a Homelite Prolite is, also anybody got a coil for it, I am getting spark but it is intermitent any ideas please PM me.

 

[Saw Dr.]

Does anybody have a good 262xp tank theyd like to do some swappin on?

Thanks

I'll swap ya one for that junk 288 Lite you got.

 

[jimbo1490]

Still looking for a large pattern Stihl bar, 36", .063. Going to run 3/8 chain so a sprocket nose is probaly not desirable as it will most likely be for .404. Have cash!

Jimbo

 

[jimbo1490]

On a related note, how hard is it to mod the small pattern bar to fit a MS880? Is it better to mod the studs? The bigger question is do the oil holes line up?

Jimbo

 

[little possum]

I'll swap ya one for that junk 288 Lite you got.

LOL, thanks for the offer, but I think Ill have to pass on that deal.

My "grandpa" ran over his with the tractor.


Thanks Terry