Swap meet...

[sefh3]

One last shot for a MS290 air filter cover...

Anybody hear from the kid lately? chainsawmanXX

Sure haven't ? Been wondering about him ?

He's been posting on facebook. Sounds like he's been busy with his job.

 

[axlr8]

Looking for the following on a MS260

clutch, drum, a piston, and looking for a wt194.

Have some parts... My stash of greenbacks...well, i think it ran away.

bump!!

 

[Arrowhead]

Last time he was here, he told me hed pay me after I shipped a part, Shipped, about 3 months ago, and still haven't gotten a single word back.

He jumped and ran.

That sucks. All my dealings were with Jacob were good. I hope he makes it right with ya.

 

[Arrowhead]

I can check and see if the dealers around here have one Ed. Maybe someone has dead stock they'll make me a deal on.

Don't worry about it. Ebay is full of them. I just thought it would be an easy part to find here..... wrong again.

 

[Overtrained]

Anyone got a usable 3/8" LP chain for a 16" .050 bar? Believe I need 54DL's.

 

[Chris J.]

Don't worry about it. Ebay is full of them. I just thought it would be an easy part to find here..... wrong again.

Fish has posted that he buys new MS290s and parts them out.

 

[sefh3]

Don't worry about it. Ebay is full of them. I just thought it would be an easy part to find here..... wrong again.

Not on here. We all making sleeper rat rods with the 039 aftermarket kits

 

[tbone75]

That sucks. All my dealings were with Jacob were good. I hope he makes it right with ya.

Me too ! I have done a LOT of dealing with him,he can be a little slow getting stuff out,but its always been great !
He is young and gets to much on his plate at once I think?

 

[Overtrained]

Me too ! I have done a LOT of dealing with him,he can be a little slow getting stuff out,but its always been great !
He is young and gets to much on his plate at once I think?

So where did the mac cat end up?:yoyo:

 

[Arrowhead]

Anyone got a usable 3/8" LP chain for a 16" .050 bar? Believe I need 54DL's.

Let me go check....

 

[Arrowhead]

Me too ! I have done a LOT of dealing with him,he can be a little slow getting stuff out,but its always been great !
He is young and gets to much on his plate at once I think?

He used to call me at least once a week also. He did have a bunch going on... new job, etc.
Still no excuse for leaving other members out to dry.
I always say... everybody is great to deal with till they screw ya for the first time.

 

[MnSam]

I'd been waiting for a MO from him for months and finally wrote it off. It wasn't a major transaction, but ... I like to think he is regrouping, and hope he gets the benefit of the doubt from the majority.

 

[tbone75]

He used to call me at least once a week also. He did have a bunch going on... new job, etc.
Still no excuse for leaving other members out to dry.
I always say... everybody is great to deal with till they screw ya for the first time.

Once is enough for most people. Just can't see why he would do that? Not like him at all ? Sure hope he takes care of it.

 

[redray46]

288 clutch/chain brake

I'm looking for a chain brake and clutch cover for an older 288xp if anyone has one. I may just have to go with the aftermarket one, but would rather have the old metal one.


Thanks, Scott

I may have one,I will check tomorrow.
RR

 

[psuiewalsh]

Looking for a flywheel nut and washer for a husqvarna 254XP. I have some stuff to trade.

 

[Arrowhead]

Anyone got a usable 3/8" LP chain for a 16" .050 bar? Believe I need 54DL's.

Let me go check....

I got a good loop of 54dl, but it's saftey chain. PM your addy and I'll pop it in the mail Monday morn.
If you need a different dl, let me know. I can spin a loop up.

 

[Arrowhead]

Once is enough for most people. Just can't see why he would do that? Not like him at all ? Sure hope he takes care of it.

I agree. Seemed like a great dude. We talked a lot on the phone and swapped a lot of saws/parts. Hopefully it will work out.

 

[scallywag]

Looking for Stihl 070 /090 Non AV Handle's front & back .

 

[HittinSteel]

I have at least 3 good used .325 68 .063 chains (2 are RSC). They will need sharpened but have a lot of life left. Came off my stihl 260. PM if interested.

 

[scallywag]

Looking for Stihl 070 /090 Non AV Handle's front & back .

I have a very good AV system i'd be willing to swap for the right parts.