Swap meet...

[Eccentric]

I can use those and I'm right across the puddle. PM sent.

I could use one of those .325-9 rims Chris if you feel like putting one in the 'circus bear box' once they arrive.

this one has the long hi and lo needles that go through a grommet in the carb box wall. it also has the external idle speee screw.

That means you can use any 10-series SDC. If you land one with short needles you can either swap in the long needles from your 'dead' carb, or plug the holes in the grommet. If the carb you end up with has the integral idle speed screw you can just back it off to where it's only "along for the ride" and the external adjustment screw is the one actually doing the work.

 

[Eccentric]

You're like a walking encyclopedia,ya know?

With paws.

Thanks Chris. It's a more useful skill than riding a unicycle. Never got the hang of that one....:jester:

 

[Warped5]

Looking for a Mac or Homelite bow bar.

Have some parts for either or ca$h.

Please PM me with what you have.

TIA

 

[MPE]

Clean 044 top cover

Looking for a clean 044 top cover, no decomp. Low on swappable things just now, but I can always swap some PayPal gift money.

EDIT: Come to think of it, also need the little disc thing that allows or restricts hot air from entering the air filter area, a 3/4 wrap handlebar in good shape, and possibly a DP front muffer cover.

As for things to trade:

I have a "only made 2 cuts with it" NOS McCulloch solid, replaceable sprocket tip 16" bar in 3/8" .050 60dl for a 10-10 and similar, as well as a 16" McCulloch hardnose with the black/silver graphics still in pretty good shape.

Also have a 3/8" .050 60dl 16" Echo (Poulan and Redmax, too) NOS 160GLHD176 Oregon Pro-lite bar, with the older graphics on it, never even mounted to a saw.

And lastly, John Deere 51SV (Echo 510EVL) in good shape, 20" LaserLite bar and 3/8" chain, new carb kit in December, paint in very good shape.

 

[jerrycmorrow]

...That means you can use any 10-series SDC. If you land one with short needles you can either swap in the long needles from your 'dead' carb, or plug the holes in the grommet. If the carb you end up with has the integral idle speed screw you can just back it off to where it's only "along for the ride" and the external adjustment screw is the one actually doing the work.

help edumacate me considering carbs. even though a carb will fit on the saw is it better to install a carb from a larger displacement saw rather than from a smaller displacement? or no difference

 

[Eccentric]

help edumacate me considering carbs. even though a carb will fit on the saw is it better to install a carb from a larger displacement saw rather than from a smaller displacement? or no difference

As long as it has H and L needles, most of the 10-series SDC carbs are the same. The fixed H-side cards have numbered H-side fixed jets inside the metering chamber. A few of the SDC's on some of the 70cc AV saws (and possibly the 82cc saws...can't recall right now) have larger bores.

 

[burnt03]

Looking for a chain brake handle for my Jonsered 630. I either need an old style handle or a new style clutch cover. Apparently, a clutch cover from a Husq 61/66/266/268/272 will also fit.

Thanks!

 

[blueberrymuzik]

MS441 Crankcase

I'm needing a crankcase for a MS441 Magnum.


Thanks!

 

[logging22]

I'm needing a crankcase for a MS441 Magnum.


Thanks!

PM sent

 

[Arrowhead]

I'm needing a crankcase for a MS441 Magnum.


Thanks!

PM sent

See... that didn't take long.

 

[husqvarnaguy]

Looking for a chain brake handle for my Jonsered 630. I either need an old style handle or a new style clutch cover. Apparently, a clutch cover from a Husq 61/66/266/268/272 will also fit.

Thanks!

Might have one of dem.

 

[vw_motorsports]

Still looking for the elusive Echo cs670 complete white clutch cover...please pm if you can help me out

bump


Looking for some

impulse lines for an 026/ms260 should fit nicely in a padded envelope

 

[Wagnerwerks]

bump


Looking for some

impulse lines for an 026/ms260 should fit nicely in a padded envelope

Are 024 lines the same?

 

[Whiskers]

Are 024 lines the same?

Yes

 

[jerrycmorrow]

looking for a Walbro SDC44 carb for a Pro Mac 60. according to my documentation a SDC 44A, 49, 58, or 58A will work as well. got some stuff from smaller saws and a little bit of worthless, green paper.

this one has the long hi and lo needles that go through a grommet in the carb box wall. it also has the external idle speee screw.

...That means you can use any 10-series SDC. If you land one with short needles you can either swap in the long needles from your 'dead' carb, or plug the holes in the grommet. If the carb you end up with has the integral idle speed screw you can just back it off to where it's only "along for the ride" and the external adjustment screw is the one actually doing the work.

gonna try this again. had some pm correspondence but i let my inbox jam up; lotsa space now. i apologize if one of yas wasted your time by encountering a full box.
i just need one where the hi and lo needles are perpendicular to the carb body rather than angled.
anyone?

 

[husqvarnaguy]

Looking for a chain brake handle for my Jonsered 630. I either need an old style handle or a new style clutch cover. Apparently, a clutch cover from a Husq 61/66/266/268/272 will also fit.

Thanks!

I have an assembly off a 670 champ. That should work.

 

[struggle]

anyone need any of these things pictured.

PM me. 038 recoil 011 clutch cover? #1123 muffler.

Getting rid of misc. stuff when I find it

 

[Arrowhead]

I can use the 038 cover.

 

[struggle]

I can use the 038 cover.

send me a PM with Addy

 

[vw_motorsports]

anyone need any of these things pictured.

PM me. 038 recoil 011 clutch cover? #1123 muffler.

Getting rid of misc. stuff when I find it

I like to take dibs on the side cover and muffler

thanks