Swap meet...

[Eccentric]

You're probably going to have to make the crankcase gasket for your 2100/2101.

I sent him a link to gasket sets.

Good deal, since those are impossible to get otherwise.

Yep. One more item checked off the list. Thanks guys!

 

[diggers_dad]

I need a chainbrake handle for a 170. I swapped for a 170 and it when it arrived, the CB was snapped off.

PP or Husky stuff to trade.

I think I have one in the basement. I'll check this evening and shoot you a PM.

 

[PogoInTheWoods]

050/051 Oil Pump Worm...Later Version

In need of the later version oil pump worm gear with the tabs that are driven by the clutch drum for an 051. If ya can help, shoot me an email at poge_at_oberlin_dot_net or a PM. With any luck, at least one of em will work.

TIA.

 

[diggers_dad]

I need a chainbrake handle for a 170. I swapped for a 170 and it when it arrived, the CB was snapped off.

PP or Husky stuff to trade.

Sorry Murph, I've got the wrong one. Mine is an 1127 series.

 

[nmurph]

Sorry Murph, I've got the wrong one. Mine is an 1127 series.

Thanks for trying.

Someone??? '08????

 

[blsnelling]

Anyone have a good 372 clutch? PM me if you do. Thanks.

 

[cat-face timber]

in need of the later version oil pump worm gear with the tabs that are driven by the clutch drum for an 051. If ya can help, shoot me an email at poge_at_oberlin_dot_net or a pm. With any luck, at least one of em will work.

Tia.

pm sent

 

[cat-face timber]

Husky 288 Case/Flywheel, gas tank and 1 muffler.


I do not want $$$, I would rather trade for project saws.

Must be Husky/Jonsered though..

thanks!

BUMP

I can send pics.

I have some spares from my infamous Husky 288 build.

 

[MechanicMatt]

Neil, if one off of a 180 works Ill ask my buddy what he's doing with the fried saw he has been hanging onto. And arkansaw guy, my buddy probably has your 028 muffler too, Ill ask him.

 

[Modifiedmark]

I got a brand new Stihl 20" Rollomatic E, .325 pitch, .063 gauge 81DL bar and two new Stihl RM chains to go with it. I also have a decent used 20" bar with the same specs to go with it.

I also have a brand new Stihl 32" 105DL .050 RS chain.

I still have a few Homelite C series perma hard tip bars, in 17" and 21". I have a couple SEZ type mount 16" hardnose and sprocket nose.

I would like a new or near new 28" bar in .050 gauge. Either large Husky mount, 93DL or Poulan/Echo or Homelite mount in 92DL and I could use 105DL .063 full skip chisel chains Oregon or Stihl branded, may consider Carlton branded.

I could also use a complete Partner P100 recoil assy with the plastic spacer that fits between the recoil and the top cover as well as the hardware for it. Also need some P-100 bar plates..

Can shoot pictures also if you want to see something in particular.

Bump......

 

[Clarkbug]

Does anyone have any file-o-plates that they never used/arent using anymore? watsonr told me that apparently Carlton is discontinuing them, which is a bummer.

Looking for a .325 semi-chisel plate, and a .375 chisel plate.

Dont have much in the way of parts, possibly some 028 bits, but also some green presidents to share. Shipping should be cheap!

Thanks!

Bumping. Hoping that someone has one of these somewhere in a drawer that they want to part with...

 

[nmurph]

Neil, if one off of a 180 works Ill ask my buddy what he's doing with the fried saw he has been hanging onto...

Yes, that CB is the same.

 

[Eccentric]

BUMP

I can send pics.

I have some spares from my infamous Husky 288 build.

Do you have any good 281/288 clutch covers to spare?

 

[MS460WOODCHUCK]

I picked up another poulan 306a today. The clutch sprocket and bearing are both shot. I have a little to trade and green paper. PM me if you have a good sprocket and bearing.

 

[Red Amor]

Hey Guys
I busted my 064 sprocket cover and fuel tank rear handle assembley tried to plastic weld the tank but um oples

anyone help Tar yeah

 

[Procut]

Do you have any good 281/288 clutch covers to spare?

HARD part to find in any condition for me. I have been looking for that part there for quite some time now for my re-build.

 

[struggle]

I picked up another poulan 306a today. The clutch sprocket and bearing are both shot. I have a little to trade and green paper. PM me if you have a good sprocket and bearing.

will the stuff off a 245A work?


Sent from my iPad using Tapatalk - now Free

 

[psuiewalsh]

Hey Guys
I busted my 064 sprocket cover and fuel tank rear handle assembley tried to plastic weld the tank but um oples

anyone help Tar yeah

Pm sent

Sent from my C771 using Tapatalk 2

 

[tbone75]

Stihl looking for a fuel tank for a MS441 & AF cover ! Anyone ?

Got trading stock & green paper !

 

[MS460WOODCHUCK]

will the stuff off a 245A work?


Sent from my iPad using Tapatalk - now Free

Yes it will.