Swap meet...

[Flat47]

In need of a clutch cover for a Dolmar 7900.

 

[kz1000]

I'm posting a few pics of parts that I got in trade, if you see something that you think is a part that you need, I will take a better picture. Some are Poulan, McCullough, Partner and who knows.
Also have a 268se/xp project saw that will need some parts including bearings, the piston and cylinder look like they will be fine.

 

[jockeydeuce]

I have 1 it worked on before the saw was straight gassed just cover shippng and its yours

Thanks for the kind offer, but the fellow whos saw needed the ignition, decided to buck up for a new one.

 

[mitch95100]

I need a 12mm 044 crankcase. PM with info.

 

[67L36Driver]

Looking for an Oregon #38033 rim/drum. Rumored to fit the Echo CS302 family. Also I discovered the dimensions indicate it will work on a small Remy SL-9 type.

Lots of old turd mag. parts or stamp money.............................

 

[DexterDay]

I have 2 brand new 3/8" X .063 X 72 DL Forester chains.

Would like to swap for .050 in either 18" (66 or 68 dl), 20" (72dl), 25" (84dl), or 28" (91dl).

Or?? Let me know..

 

[surfincr]

this may be a long shot since i havent seen much of either for sale but looking for an hs81t spur gear cover and spur gear as well as ether a br600 cylinder or engine. have some stihl parts kicking around and of course green

 

[Mastermind]

I need an early 066 case half......PTO side.

I have parts or cash to trade.

 

[tomdcoker]

I bought a promac 700 and need a top handle and sawdust guard for it. I have paypal and things to trade. Tom

 

[psuiewalsh]

I bought a promac 700 and need a top handle and sawdust guard for it. I have paypal and things to trade. Tom

I have one off a 10-10 but no rubber on it though

 

[cat-face timber]

I bought a promac 700 and need a top handle and sawdust guard for it. I have paypal and things to trade. Tom

Would one from a mac 610 Work?

 

[tomdcoker]

I have one off a 10-10 but no rubber on it though

I think that I have one without the rubber. I hope to find one with the rubber. There is one on ebay for about 35.00. I was hoping to get one for less. Thanks anyway. Tom

 

[tomdcoker]

Would one from a mac 610 Work?

The 610 will not work. I think the 10-10 will work, but I will have to check to be sure. Thanks anyway. Tom

 

[Jacob J.]

I need an early 066 case half......PTO side.

I have parts or cash to trade.

I think I have that...

 

[kc4sfe]

I am looking for a clutch for an ECHO 702VL. Anyone have one? I will have some parts and PayPal e-paper to trade. I'm not sure what I'm getting but I have a batch of old saws coming today. I know that I have a few Stihl parts and lots of old Poulan 2150 parts.

TIA

Lane

 

[lumberjackchef]

I am looking for a clutch for an ECHO 702VL. Anyone have one? I will have some parts and PayPal e-paper to trade. I'm not sure what I'm getting but I have a batch of old saws coming today. I know that I have a few Stihl parts and lots of old Poulan 2150 parts.

TIA

Lane

701 be the same maybe? Saws look very similar...I have one of those I think.

Sent from my XT1031 using Tapatalk

 

[kc4sfe]

I'll check the list and try to find a part number. I know that it is different than the one on the 602vl though.

 

[axlr8]

If I can't weld it up, I will be in need of a 045 muffler. Got stuff and Pres'es

i think i have a few...

 

[axlr8]

looking for a 330 homie parts saw.... need top handle and a few small bits...including the intake boot...

it was a runner!!!

 

[nstueve]

Anyone got a chunk of Oregon 75 (CJ or JGX) skip?
Have a 114DL chain and need to make it longer...

Any Oregon chisel 3/8 skip should work... I have about 75% life left in the chain so preferably nothing ground down to the nubs.