warjohn
Addicted to ArboristSite
Bigjohnston might have some of the stuff you need I will have him take a look. I would do it myself but I will be out of town until Monday.
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
Bigjohnston might have some of the stuff you need I will have him take a look. I would do it myself but I will be out of town until Monday.
warjohn
Addicted to ArboristSite
I am still interested but have been crazy busy and will be until the end of the week. PM me what you think would be reasonable.
Looking for a crankcase for an 021, 023 or 025 flippy cap is fine. Also could use a clutch cover. I have some nos stihl parts or $$$
That would be great, got the clutch side cover and chainbrake parts covered, still open for the rest.
Pioneerguy600
Mastermind
Work Saw Specialist
I need a starter, flywheel, and coil for a 021, ms210. I have one with easy start and don't like it much.
Translation: pulling that little ripcord makes him feel like a fairy. I know, I tried one and didn't like it either.
mweba
Addicted to ArboristSite
Looking for 088....clutch cover,lower av mounts (same as many saws incl 038), oiler drive clutch side, rear filter cover, intake boot, and top handle. Have parts saws for trade or solid running 038 super for 088 parts saw. PM for details. O yes and ofcourse greenbacks.
Last edited:
parrisw
Tree Freak
I may have some mounts, I'll have to look. PM me so I don't forget.
SawGarage
Addicted to ArboristSite
makes them feel like they have no compression
but i guess that's the point, huh?
wigglesworth
Booned
Anybody have a carb and throttle cable for a Stihl FS85 trimmer?
little possum
Crash and Burn
Mastermind
Work Saw Specialist
Translation: pulling that little ripcord makes him feel like a fairy. I know, I tried one and didn't like it either.
Well there is more to it than that. I'm thinking I have a mixed up frankensaw here. It has no compression release, and according to my IPL it should have. I'm of the belief that some has stuck the wrong shortblock in this case, or something.
I've got a lot of time and some cash invested in this saw and want to make it right before I try to sell it. New bearings and seals, and a new piston kit. Cleaned up nicely. I just want to finish it off right.
SawGarage
Addicted to ArboristSite
Well there is more to it than that. I'm thinking I have a mixed up frankensaw here. It has no compression release, and according to my IPL it should have. I'm of the belief that some has stuck the wrong shortblock in this case, or something.
I've got a lot of time and some cash invested in this saw and want to make it right before I try to sell it. New bearings and seals, and a new piston kit. Cleaned up nicely. I just want to finish it off right.
guess I don't want it then... :spam:
mweba
Addicted to ArboristSite
Cleaning out the shop. Have a pair of Gilmer reduction belts. Both are out of a Clinton at 3:1. Labeled H 2 and H 4. 1.01 in width. I believe some Homies used these but unsure of the compatibility.
bigjohnston
ArboristSite Operative
I know I don't have a clutch cover but I may have the rest of it I definately have a trigger module and choke rod let me know if you need any of it still
little possum
Crash and Burn
Hey fellas, anybody have some spare 044 plastics, wrap handle, gas tank?
Plastics can be ugly, just prefer no major cracks.
Parts and a little $
Plastics can be ugly, just prefer no major cracks.
Parts and a little $
Mastermind
Work Saw Specialist
guess I don't want it then... :spam:
I think it's gonna turn out way too nice for your taste. :spam:
Cleaning out the shop. Have a pair of Gilmer reduction belts. Both are out of a Clinton at 3:1. Labeled H 2 and H 4. 1.01 in width. I believe some Homies used these but unsure of the compatibility.
You'll have to measure the pitch but it doesn't look to fit the Homelite belt reduction.
Chris B.
Just bumping up in case someone has interest. I like $$$ too.
