I might have a new or near new 28" Cannon .050 gauge in my stack at home, I'll look on my next day off.
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
I might have a new or near new 28" Cannon .050 gauge in my stack at home, I'll look on my next day off.
Johndirt82
ArboristSite Operative
Good deal. I like the 32rw but trying to get stihl chain in socal in 063 gauge is near impossible. thanks again Jacob J. btw the 272xp runs like a champ with that piston and Cyl I got from you.
Yeah that piston was an unusual one. I got it in a large lot of NOS parts I bought from a retiring mom and pop duo that ran a saw shop and rental store for years. Husky had made that piston originally for the 272k cut-off saws and found that it made more power in the chainsaws as well. It was right before the 272 and 272 XPs were discontinued.
Chris J.
Addicted to ArboristSite
What I have:
Misc Stihl 009 & 011 parts. Some will probably go to Saw Dr., but I'll stihl have plenty left over.
A very clean Stihl 015 with a bad ignition, but I have a spare ignition (supposedly good, I never tested it).
Enough drum sprockets to give an elephant a hernia; there's an old thread here at AS.
What I'm looking for:
Clutch cover for a Jonsered 670. I'd like OEM, but sometimes you can't tell if the knee-joint is sound until you start cutting, so a more modern Husky or aftermarket cover would be fine. Yes, I know that AM covers are available from Bailey's & on eBay.
20" bar & chain for Stihl MS 361. I got it with a like new 25" Stihl Rolomatic ES (3/8, 25, 63, 84). I might keep it, but I'm open to trade offers.
Misc Stihl 009 & 011 parts. Some will probably go to Saw Dr., but I'll stihl have plenty left over.
A very clean Stihl 015 with a bad ignition, but I have a spare ignition (supposedly good, I never tested it).
Enough drum sprockets to give an elephant a hernia; there's an old thread here at AS.
What I'm looking for:
Clutch cover for a Jonsered 670. I'd like OEM, but sometimes you can't tell if the knee-joint is sound until you start cutting, so a more modern Husky or aftermarket cover would be fine. Yes, I know that AM covers are available from Bailey's & on eBay.
20" bar & chain for Stihl MS 361. I got it with a like new 25" Stihl Rolomatic ES (3/8, 25, 63, 84). I might keep it, but I'm open to trade offers.
tmessenger
ArboristSite Guru
Trade: Jonsered 920 also have a Remington Super 754
Got a J-Red 920, piston was scored so I pulled the jug, the jug looks OK to me (see photo showing exhaust) port. The saw is missing the dog and the cloak lever. Cylinder has some broken fins on the front drive side, front left side of the top plastic engine cover is cracked and one of the muffler bolt threads has been helicoiled. Clutch cover has a couple of cracks over the clutch drum area. Bar studs are gone, they were using bolts in place of the studs. Crank turns smoothly, has a couple of thousands of end play (update: I check this again there is no end play in the crank it's tight just me flexing the crank pulling too hard on the top of the flywheel) . Two of the four screws that hold the starter cover on are metal screws ( but hold good). Coil is good, nice hot blue spark. Comes with a nearly new 20" Oregon bar and used chisel chain.
My wish list is to trade for a Stihl 020 rear handle saw.
I also have a Remington Super 754 parts saw.
Got a J-Red 920, piston was scored so I pulled the jug, the jug looks OK to me (see photo showing exhaust) port. The saw is missing the dog and the cloak lever. Cylinder has some broken fins on the front drive side, front left side of the top plastic engine cover is cracked and one of the muffler bolt threads has been helicoiled. Clutch cover has a couple of cracks over the clutch drum area. Bar studs are gone, they were using bolts in place of the studs. Crank turns smoothly, has a couple of thousands of end play (update: I check this again there is no end play in the crank it's tight just me flexing the crank pulling too hard on the top of the flywheel) . Two of the four screws that hold the starter cover on are metal screws ( but hold good). Coil is good, nice hot blue spark. Comes with a nearly new 20" Oregon bar and used chisel chain.
My wish list is to trade for a Stihl 020 rear handle saw.
I also have a Remington Super 754 parts saw.
Last edited:
Mastermind
Work Saw Specialist
Seeking a 24" - 28" bar for a stihl, hardnose will work, but of course a sprocket is better, 3/8 pitch. I have trade fodder and a little green.
Bowtie
Gearhead
PM sent.
brad_ruch
ArboristSite Member
25in bar for a 038 Super
looking for a stihl 25in bar for a 038 super.I have a 20in ES Bar on it I would trade.
looking for a stihl 25in bar for a 038 super.I have a 20in ES Bar on it I would trade.
SawGarage
Addicted to ArboristSite
I'm gonna 2nd the Stihl bar request... OH!, wait, make that 3rd after brad_ruch
I could use a decent quality 24-32" bar for 3001 (is that the 044/066, etc mount?) and one for a 3003 mount. I have a BRAND new 16" stihl bar in 3003 mount
, as well as (2) new and (3)almost new 16" chains 
Could maybe also use another 20" bar too....all in 3/8"
I have SOME green, husky bars to trade, nos older stihl, and husky parts.
OH...for I forget....does ANYONE?!?! have a 066 flat-top chain brake handle for a 1/2 wrap handle??? please ?? someone? am I begging? hell....I AM BEGGING! forestryworks??
Chris J.
Addicted to ArboristSite
What are the specs on your bar? I'm looking for a 20" bar for my 361, it currently has a 25" bar (nearly new, good chain) on it.
Looking for a clutch shoe for a 371/362/365/372/2065/2165/2171....
I have green backs and parts galore.
I have green backs and parts galore.
Yeah it's too bad they don't sell the shoes separately...
I think I have an extra off a broken clutch I can send your way.
Ya, I was a little surprised when I saw you have to order an entire clutch.
Should have waited for my clutch removal tool to show up before trying to take it off, but have done numerous 372's before with no problems. It would be nice if all clutches had the 19mm nut like stihl pro saws.
If you have one, that would be appreciated, otherwise I might buy a new AM cltuch from Lucas at MagSupply....
Saw Dr.
Junk Collector
I have a Mac 310/320 that has compression and spark. Missing parts from the chain brake and the muffler bolt holes are stripped. Anyone need any parts?
I need a good p/c off a AH47 for my Sears 917.60049, or at least a good cylinder. I swear it looks like my cylinder is cracked in the top, up around the spark plug. Anyone ever seen that happen? The last picture is the saw I need parts for.
I need a good p/c off a AH47 for my Sears 917.60049, or at least a good cylinder. I swear it looks like my cylinder is cracked in the top, up around the spark plug. Anyone ever seen that happen? The last picture is the saw I need parts for.
Also looking for a 036 cylinder. I have a 034 and a 036 meteor piston waiting to come back to life......
roncoinc
Official Stihl Disser
I'm gonna 2nd the Stihl bar request... OH!, wait, make that 3rd after brad_ruch
I could use a decent quality 24-32" bar for 3001 (is that the 044/066, etc mount?) and one for a 3003 mount. I have a BRAND new 16" stihl bar in 3003 mount
Could maybe also use another 20" bar too....all in 3/8"
I have SOME green, husky bars to trade, nos older stihl, and husky parts.
OH...for I forget....does ANYONE?!?! have a 066 flat-top chain brake handle for a 1/2 wrap handle??? please ?? someone? am I begging? hell....I AM BEGGING! forestryworks??
You got a B&C to fit an 026 ??
Mastermind
Work Saw Specialist
What in the hell are you doing with a 026. last time I checked that was a creamsickle. LOLOLOLOL
sefh3
Addicted to ArboristSite
I think Ron likes those creamsickles (LOL). He's coming out of the closet on us. He just posted a video of him runnin an 041.
