smilin possum
Addicted to ArboristSite
I got some of them for ya BBB.
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
I got some of them for ya BBB.
SawGarage
Addicted to ArboristSite
Work Saw Collector
GTG Coffee Maker
Wanted 038 full wrap handle, I have a half wrap if needed for a trade and boot maybe other 038 parts. I know its a long shot just got to try.
little possum
Crash and Burn
Yea J, thats bout it. haha. Handle took most of the impact, but took a corner outta the case and a AV mount out with it, and the gas tank is wrinkled, the running works were fine.uM....WAS THERE ANYTHING LEFT to the saw but the top end stuff???
J
bigwhiteash
ArboristSite Member
swap meet
Hi all! I need a handle/gas tank for a Shindaiwa 488; also a throttle/trigger and hand guard[white plastic pc]for an Echo 650evl.
I have an Echo 500vl[post recall!] complete up for grabs and lots of older Homelite saws, including a SXL925,SXL, 150auto and an SEZ auto, complete/running. Thanks! J
Hi all! I need a handle/gas tank for a Shindaiwa 488; also a throttle/trigger and hand guard[white plastic pc]for an Echo 650evl.
I have an Echo 500vl[post recall!] complete up for grabs and lots of older Homelite saws, including a SXL925,SXL, 150auto and an SEZ auto, complete/running. Thanks! J
Mastermind
Work Saw Specialist
I have some Shinny 416 parts, probably no help??? What do you want for the SXL925???
Eccentric
Mister Wizard
Rats. I knew I should have gotten up earlier. Also interested in the SXL925, and maybe the SXL and/or the Super E-Z Auto. Not into 150's...
What other old Homelites do you have to part with?
Yeah, I missed that post too, I have been itching to get an XL900/925 style saw.
Jim
Kwdog75
Addicted to ArboristSite
Looking for the small round piece that goes between the carb and intake on an 026. PM me please. Need a few ASAP!
Mastermind
Work Saw Specialist
I thought I could stand to leave it be, but I can't stand half assed stuff. I need a pto side case half for a 046/460. The felling dog won't stay attached to JB weld. 
bcorradi
Arboristsite.com Sponsor
I may have some laying around. Are you looking for the brass piece that goes inside the intake or the aluminum one that goes around the outside or both? Please send me a pm with your address and details.
turbo885
ArboristSite Operative
Stihl parts
i have no idea what model saws this stuff is from if you see somthing you can use pm me. i will get part numbers if you need them i need husky parts most anything for a 372 also need a chain brake handle for a 262 / 61 / 268
Thanks BILL
i have no idea what model saws this stuff is from if you see somthing you can use pm me. i will get part numbers if you need them i need husky parts most anything for a 372 also need a chain brake handle for a 262 / 61 / 268
Thanks BILL
Saw Dr.
Junk Collector
i have no idea what model saws this stuff is from if you see somthing you can use pm me. i will get part numbers if you need them i need husky parts most anything for a 372 also need a chain brake handle for a 262 / 61 / 268
Thanks BILL
Probably waaayyy late on this, but PM sent.
husky 35 / 37 brake handle
Been looking for a while. Haven't found anything on e-bay, no responses to the want ad, so I'll try here one more time. I have a husky 35 in good condition, except for a damaged brake handle. The same handle was used on a Husky 37, I think, as well as a Pioneer/Partner 330/350, possibly others. Not too concerned if it's orange or black, I'd just like it to be there. I could probably fabricate a piece of ABS to do the job, but it'd be nice to have the real thing.
All of the linkage parts are there, and the brake works, just the plastic is pooched. Not much to trade but clams.
Been looking for a while. Haven't found anything on e-bay, no responses to the want ad, so I'll try here one more time. I have a husky 35 in good condition, except for a damaged brake handle. The same handle was used on a Husky 37, I think, as well as a Pioneer/Partner 330/350, possibly others. Not too concerned if it's orange or black, I'd just like it to be there. I could probably fabricate a piece of ABS to do the job, but it'd be nice to have the real thing.
All of the linkage parts are there, and the brake works, just the plastic is pooched. Not much to trade but clams.
Last edited:
roncoinc
Official Stihl Disser
HHmmm... i got a runnin 904 ?
was going to put a module in it,seems like it got points floating at high rpm.
Eccentric
Mister Wizard
Duke Thieroff
Fill your hands, you SOB!
Does anybody have a Mac 10-10 project saw, or one in running condition they'd like to sell/trade?
CT
CT
PM sent
Ms290
I am in need of a rear handle for a MS290. I don't have a lot to trade, but would be willing to pay a fair price. Thanks.
I am in need of a rear handle for a MS290. I don't have a lot to trade, but would be willing to pay a fair price. Thanks.
Saw Dr.
Junk Collector
Flat-top or rounded-top?
