Swap meet...

[67L36Driver]

Remington Super 75A air filter. And/or a parts saw.

Mostly small stuff in my sig. to trade, or dead presidents.

 

[67 Mustang]

Poulan Pro 405

Need a Poulan Pro 405 parts saw. Top end toasted OK.

 

[STLfirewood]

I need a good jug for a MS290. I just need the jug. I don't need the pistone or anything else. PM me a price shipped to zip code 63050.

Thanks Scott

 

[Duke Thieroff]

Looking for just the clutch cover for a Mac double eagle 50 or Titan 50 or any other known analog.

Or a parts saw If anyone has one.

Chris

 

[firefighter33]

Well fellas im going to put it out there... Ive got a 880 Mag that im thinking about putting up for trade. It complete minus the crank,bearings,seals and piston. I have a thread started with pics. Parts are crazy exspensive and i just dont have the cash to make it work and it kills me to see it just sitting on the bench. Im looking for 90cc+ saw for trade. Pm box is pretty empty so send em in.:msp_thumbsup: And no im not going to give it away!:biggrin: Ive got a good bit invested but im open to offers. LMK what ya got.

 

[dh1984]

i got a homelite super xl starter cover that i just found in my shed that i have no use for.it still has the pull rope and the kill switch and wire on it and the starter pulley.Pm me if anyone needs it.

 

[cat-face timber]

Stihl MS250 Flippy Cap and Starter Pawl needed

I recently traded for a MS250 and I need the Starter Pawls.
Also need the Fuel Cap (Flippy Cap)


If you have any handy please send me a PM.

Thanks!
:help:

 

[sefh3]

I could use a piston and cylinder for an Stihl 046 project I have. If you have one, PM me. I could also use a piston and rings for an 036 too. I have parts to trade.

 

[tlandrum]

i need a crank for an ms460

 

[tomdcoker]

want list

My want list is growing. I now need a Zip Or Wiz cylinder. A Stihl 025 Crank and a Stihl 029 Muffler.
The 029 had a round with a tree and two of the slots where the muffler bolts go are broken out. Does anyone have a good solution to this problem other than replacing the cylinder. Tom

 

[stihl_collector]

I'm chasing a P&C, crank and clutch for a Stihl 064AV if anyone can help.

I have cash only so pm me if u can help.

Thanks.

 

[Modifiedmark]

My want list is growing. I now need a Zip Or Wiz cylinder. A Stihl 025 Crank and a Stihl 029 Muffler.
The 029 had a round with a tree and two of the slots where the muffler bolts go are broken out. Does anyone have a good solution to this problem other than replacing the cylinder. Tom

Tom, I plumb forgot about that crank, I even got it out for you, just forgot to send it. Sorry.

 

[Jacob J.]

My want list is growing. I now need a Zip Or Wiz cylinder. A Stihl 025 Crank and a Stihl 029 Muffler.
The 029 had a round with a tree and two of the slots where the muffler bolts go are broken out. Does anyone have a good solution to this problem other than replacing the cylinder. Tom

I still have your Wiz/Zip cylinder. If two of the exhaust mounts are broken out, you could possibly have them welded back up. I had a 394 that broke a large chunk out of one side of the exhaust port where the muffler mounts on and a guy was able to weld it all back for me and then I re-shaped the mount.

 

[terry2tmd]

Need climbing saw

Hey guys been kinda busy these days. I need a climbing saw I like stihl and husky saws. Everything I have read says the stihl 200t is the way to go, and thus they are super expensive. I am not getting into pro climbing, it has become a once in a while thing for the elderly mostly. A ms391, or a 288xp especially with a 28"bar @ 30 feet, topping out a old chinese elm, ain't a good time. I did it I only had to change my shorts once, these saws do their best topping when you start at the base not the top. Pretty much I would be happy with a good 338xp.
I got a homelite super IV, that I found, a pioneer 1200 automatic, that needs fuel lines, and clutch cover, and if the saw is in good shape, I could be talked into letting my 288 go be warned this saw needs a chain break, and a new flywheel.
Like I said I don't use a little saw like this alot, but when I need it I need it, that's why I would prefer a Stihl or husky.

 

[jockeydeuce]

I'm chasing a P&C, crank and clutch for a Stihl 064AV if anyone can help.

I have cash only so pm me if u can help.

Thanks.

I have all your 064 needs covered, but your PM box is full.

 

[tomdcoker]

I still have your Wiz/Zip cylinder. If two of the exhaust mounts are broken out, you could possibly have them welded back up. I had a 394 that broke a large chunk out of one side of the exhaust port where the muffler mounts on and a guy was able to weld it all back for me and then I re-shaped the mount.

Weld it back with what? Tig, stick or braze. I will P M you my mailing address.

 

[terry2tmd]

I still have your Wiz/Zip cylinder. If two of the exhaust mounts are broken out, you could possibly have them welded back up. I had a 394 that broke a large chunk out of one side of the exhaust port where the muffler mounts on and a guy was able to weld it all back for me and then I re-shaped the mount.

I got a 394 cylinder in the same shape, clean as can be inside but busted out exhaust, wanna try your hand at fixing it, I can send it to you.

 

[Duke Thieroff]

Looking for just the clutch cover for a Mac double eagle 50 or Titan 50 or any other known analog.

Or a parts saw If anyone has one.

Chris

Anyone?

Chris

 

[Jacob J.]

Weld it back with what? Tig, stick or braze. I will P M you my mailing address.

My guy TIGs them up. I've never watched him do it.

I got a 394 cylinder in the same shape, clean as can be inside but busted out exhaust, wanna try your hand at fixing it, I can send it to you.

Sure, I could give it a shot. I'll PM you my addy.

 

[valekbrothers]

Walbro Carb Needed

I'm looking for either a complete walbro carb, or just the high mixture needle for this carb.......

It is off of a Tecumseh T200 engine.

Any help or info would be greatly appreciated.

Thanks,
Chuck