Swap meet...

[Modifiedmark]

Looking for:

Husqvarna

2101 tank breather


Homelite 360

Air Filter
Carb Boot
Sprocket Nose bar Oregon d196



Chris

Chris, you sure you need a D196 bar for a 360? Most had 5/16" studs and used the old Homelite mount like the Super EZ used or the modern replacement, the K095 small Husky mount.

 

[Modifiedmark]

I sure will. :msp_tongue:

I was hoping to have a 3/8 bar on the 330 by Sat. I've got a NOS 16" 3/8 Poulan Pro bar coming but doubt it will be here in time. If not I'll stick a Wild Thing 3/8 lowpro on it.

I already looked and I don't have a spare 16" 3/8's bar for that. I do have a 20 I can bring if you want to try that.

 

[Mastermind]

I already looked and I don't have a spare 16" 3/8's bar for that. I do have a 20 I can bring if you want to try that.

I have plenty of small bars that will work so we can play.

 

[tomdcoker]

I think they have a different thread for that.

Probably a different forum. Tom

 

[Brushwacker]

I have some small mount Husky bars, think they are KO95. 1)new Oregon powermatch 84 DL 58 gauge, 1) used hardnose that I think is 28" 50 gauge in good condition, and a couple new 20" 70dl 50ga powermatch.
I have 4) Oregon powermatch 58 gauge 24" also that originally fit large Husky, I had them milled to fit Stihl. Originally they were 84 dl but milled for the Stihl it left little to no adjustment so the chains need cut 83 dl.. Have some 058 gauge Stihl rs chisel chain also I could let go with a bar.
I could use some .325 pitch chain semi-chisel .063 and a little .058 or some 18" loops. No safety chain. Also would like to have an new or excellant 044 10mm wr pin piston, rings,pin. if I can strike a deal with 1 soon. Any very good or new Stihl mount (026 t0 660) bars in 3/8 50 gauge may interest me also, and larger model Stihl parts or project saws.

 

[Duke Thieroff]

Chris, you sure you need a D196 bar for a 360? Most had 5/16" studs and used the old Homelite mount like the Super EZ used or the modern replacement, the K095 small Husky mount.

According to Acres:

Reference: 14
Carlton: 20/21
Oregon: D196, D096
Windsor: UXL or TXL
GB: HN
Tsumura:
OEM:

Comments: HOMELITE

I know its not always accurate.

Acording to Bailey's the K095 will not fit, but will fit some 300 series saws.

Chris

 

[Modifiedmark]

According to Acres:

Reference: 14
Carlton: 20/21
Oregon: D196, D096
Windsor: UXL or TXL
GB: HN
Tsumura:
OEM:

Comments: HOMELITE

I know its not always accurate.

Acording to Bailey's the K095 will not fit, but will fit some 300 series saws.

Chris

Chris, if you have 5/16" studs, the K095 bar is the one you want, the D196 bar will need stud spacers and will have to oil though the adjuster holes to work.

Do a search here, I posted photos long ago.

 

[Duke Thieroff]

Chris, if you have 5/16" studs, the K095 bar is the one you want, the D196 bar will need stud spacers and will have to oil though the adjuster holes to work.

Do a search here, I posted photos long ago.

Well, would you look at that.

Mark knowing his stuff, again. Thanks bud!

I do have a hardnose I can throw on it for the time being. It won't be a runner for awhile yet, I have bigger projects to be working on.

Mark, that Husky has some stones man. I only ran it for a short time and was quite impressed.


Chris

 

[Wildman1024]

The homelite 360 does take a D196 bar mount.

 

[nmurph]

I am looking to trade for a BP blower. It doesn't have to be a monster and I am not really brand specific; Echo, Stihl, Redmax...etc. I have a BG 85 and it is a little smaller than what I could use. I have several saws to trade.

Bump

 

[nmurph]

i need the following for a 288-

top cover - no preference on hi/lo top - i have to order the filter as well
coil-
operator presence lever - AKA safety interlock.
flywheel fan shroud
manifold insulator - AKA carb box partition

green backs to trade.

Bump

 

[nmurph]

I have 18" Homelite sprocket nose bar. It is in above average shape. It isn't new, but it has LOTS of life left. I believe the chain was .325 Oregon SC. I don't know where it came from as I found it in the bottom of a box that i got something saw-related in. I was going to throw the box on the burn pile and thought it felt a little heavy. i dug through the packing material and found the bar.
Anyway, I don't need the bar and if someone would like it, we can work something out. I would be interested mostly in SM Husky bars. It has the following stamping on it:

C40 Homelite
PT20381-D5

Bump

 

[redunshee]

Manual Oiler

Anyone have a manual oiler pump for a Poulan Pro 655BP?

Bob

 

[kscycler]

Need a few Stihl 028 parts to revive this parts saw

I'm trying to save an 028AV WB EQ that I found at the local Stihl dealer. Need a flywheel (1118 400 1206), muffler exhaust casing (1118 145 0801), one slotted nut that holds the filter on (1113 141 8305), and a handle sleeve (1118 791 7200)(also known as screw assembly? 0000 790 6101). Thanks, Eric, for the starter stuff. Son in law will get an early Christmas if things work out...

 

[Mastermind]

I'm trying to save an 028AV WB EQ that I found at the local Stihl dealer. Need a flywheel (1118 400 1206), muffler exhaust casing (1118 145 0801), one slotted nut that holds the filter on (1113 141 8305), and a handle sleeve (1118 791 7200)(also known as screw assembly? 0000 790 6101). Thanks, Eric, for the starter stuff. Son in law will get an early Christmas if things work out...

You can update that saw to the newer air filter and cover screw. It may be easier to find. If you need and wrap handle instead of the handle sleeve let me know, I have an extra. I might have that flywheel.

 

[kscycler]

Thanks for the info. I'll try to find an updated filter. The flywheel is on its way, thanks to another member's generosity. I appreciate it...

 

[blstd]

I need a chain brake/clutch cover for a Jonsered 2094.

Thanks!

I'm still looking. Please PM me a price if you have one.

Thanks!

 

[DSS]

I'm looking for a muffler and a flywheel cover for a RH start mac 10-10.

As you can see the lower part is there, I need the upper section.



This is where the cover I'm talking about fits.

I found the cover, but mine is all one piece. If you think this will fit, it's yours.

 

[Mastermind]

I'm looking for a muffler and a flywheel cover for a RH start mac 10-10.

As you can see the lower part is there, I need the upper section.



This is where the cover I'm talking about fits.

I found the cover, but mine is all one piece. If you think this will fit, it's yours.

Looks like it will fit. Maybe some mac heads could post up to let us newbies know for sure.

 

[Arrowhead]

MS290 parts needed

I need a muffler, E clip that holds the clutch, the 2 screws that hold the coil, the 4 starter cover screws with the brake lever bushing. I also need all the screws that are on the front handle.

I got some parts and some green.