Swap meet...

[barneyrb]

I have put together a JRed 2036 for an unemployed guy I know here and the coil went bad. Has anyone got a coil from a 2036-41, Husky 36, 41, 136, 141, or I think any Poulan that bolts to the cylinder will work. It will not take the coil that bolts to the plastic case but has to go on the cylinder with about 3-4" of lead on it.

I've got stuff to trade or green. Let me know......

bump

 

[cowroy]

I have a nearly new Husqvarna 346xp For sale or possible trade listed in the classified HERE and just wanted to get it out there more that at this price, it is free shipping to the lower 48. Might trade for the right item.

 

[wendell]

Nice touch putting it on the trophy.

 

[cowroy]

Nice touch putting it on the trophy.

:msp_biggrin:

 

[djones]

I'm looking for a fair to good bar for an 064 in the 24" to 30" range. I've got some mac parts and some 020 and 015 parts, some 021 and 029 parts, a homie c-52 project saw and a poulan 2150 parts saw. Also available a couple of pro mac 10-10 runners. Check your bar stock and let me know what you've got.

 

[kscycler]

028 Flywheel with points

Need a flywheel for 028 with points. Believe the P/N is 1118 400 1205. Have a 1118 400 1206 (electronic) for trade (bought the wrong one, D'uh!). thanks...

 

[Duke Thieroff]

Looking for a couple of 79 linkers in .375 .058

Got some stuff to trade or some paper to help start the wood burner.


Chris

 

[Duke Thieroff]

Looking for a couple of 79 linkers in .375 .058

Got some stuff to trade or some paper to help start the wood burner.


Chris

Could also use a couple largne spline rim sprockets in the 3/8s variety

 

[Eccentric]

Looking for a couple of 79 linkers in .375 .058

Got some stuff to trade or some paper to help start the wood burner.


Chris

For your big P/P (LOL........now get yer mind outa the gutter)? That's an odd DL count. Old Homelite/McCulloch/Poulan is 81DL of .375" for a 24" bar. I freely admit that I don't know jack about P/P saws though.:hmm3grin2orange:

 

[Duke Thieroff]

For your big P/P (LOL........now get yer mind outa the gutter)? That's an odd DL count. Old Homelite/McCulloch/Poulan is 81DL of .375" for a 24" bar. I freely admit that I don't know jack about P/P saws though.:hmm3grin2orange:

The only P/P around here that comes in the 24" variety has to come by Postal Delivery!

I thought it was an odd link count myself, but I wonder if it's actually a 23" marketed as 24" bar, or some metric job.


I know very little about P/Ps myself (both types) other than a little work I did on a Farmsaw and this tank. Everyone who has had a chance at it was throughly impressed. I hope to pack it to another GTG sometime for wide eyes and stained pants.


Chris

 

[Eccentric]

The only P/P around here that comes in the 24" variety has to come by Postal Delivery!

I thought it was an odd link count myself, but I wonder if it's actually a 23" marketed as 24" bar, or some metric job.


I know very little about P/Ps myself (both types) other than a little work I did on a Farmsaw and this tank. Everyone who has had a chance at it was throughly impressed. I hope to pack it to another GTG sometime for wide eyes and stained pants.


Chris

You're sure that's not a .404" bar Chris? Ah hell..........I don't know anything about those saws so I'm just pissing in the wind here...nevermind...:taped:

Just made my 3100th post a few minutes ago. Was inspired by your 1000th. You can guess where I made said post. I thought it was amusing that my 3100th post gave me 1010 credits...:jester:

http://www.arboristsite.com/chainsaw/101147-179.htm#post3031886

 

[Mastermind]

Need a flywheel for 028 with points. Believe the P/N is 1118 400 1205. Have a 1118 400 1206 (electronic) for trade (bought the wrong one, D'uh!). thanks...

Just get an electronic coil and you will be good to go.

 

[wigglesworth]

Still looking for a MS460 cylinder. Also needing a coil (p.n. 1314) for a 460/660. I have tons to trade, and $$.

 

[Madsaw]

Just picked up a 575 xp. Needs crank bearings. Also a piston. Other then that its all tore down and ready to be cleaned up and reassembled.
Bob

 

[Mastermind]

I'm getting rid of some saws

I need to move these saws. They all run, most run very well. PM me with questions.

Stihl:

028 Super
S-10

Husqvarna:

Ported pop-up closed port 55
Mildly ported, stock numbers 2101

Homelite:

C-7
XL-12

Poulan:

Ported pop-up Poulan Pro 330
Sand cast H-200

McCulloch:

Two 35s
10-10 RH Start

 

[Logger4Life]

084

I am looking for some 084 parts top handle clutch and clutch cover. etc

 

[heimannm]

I am in need of one (1) front/lower handle mount for my Jonsered 930, PN 504 12 50 34.

Lots of parts, saws, etc. to trade, or cash if that is better.

Mark

 

[Chris J.]

I am in need of one (1) front/lower handle mount for my Jonsered 930, PN 504 12 50 34.

Lots of parts, saws, etc. to trade, or cash if that is better.

Mark

Mark, according to the IPL the 920 uses the same part. I can check my 920 in the AM, or I'll find the photos I posted in a thread here, but it's pretty much a carcass.

 

[o8f150]

I have a nearly new Husqvarna 346xp For sale or possible trade listed in the classified HERE and just wanted to get it out there more that at this price, it is free shipping to the lower 48. Might trade for the right item.

wish i had the cash right now to buy it straight out,,,,, been wanting one

 

[Mastermind]

I need to move these saws. They all run, most run very well. PM me with questions.

Stihl:

028 Super
S-10

Husqvarna:

Ported pop-up closed port 55
Mildly ported, stock numbers 2101

Homelite:

C-7
XL-12

Poulan:

Ported pop-up Poulan Pro 330
Sand cast H-200

McCulloch:

Two 35s
10-10 RH Start

I think the PP 330 is spoken for but the others are still up for grabs.