Mastermind
Work Saw Specialist
Thanks a lot Will. I found a good deal on feebay. It's on the way.
I am in need of a wrap handle for an 026. Cash, trade.......
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
Thanks a lot Will. I found a good deal on feebay. It's on the way.
I am in need of a wrap handle for an 026. Cash, trade.......
sefh3
Addicted to ArboristSite
I'm searching for a rear AV for a Stihl 020AV. This is the one that has the long rear handle on it. Cash, parts..... PM me if you have one.
zogger
Tree Freak
wonder adapter
well, you got the old one for size comparisons, now start hunting for a similar size lawnmower engine flat muffler. Braze a flat plate on the back for the mounting holes maybe...I don't know what ytour exhaust looks like, only picked up one of them twice...
Would a real small old toasted cylinder from another saw maybe work, as something to start with, a l;ittle cutting and dremel work? I mean, is it an absolute that it has to be steel?? Cut it down, install sideways with a plate or something? Just thinking out loud, I love cob jobbing stuff....a finned muffler..sharp.....
Of course I can only lu####lly dream of owning a 3120, so maybe my ideas aren't real practical on such a valuable saw and you should just suck it up and buy a new muffler, then go cut one cord and sell it to pay for it....heck, a lot of areas of the country a half a cord goes for a benjamin...
well, you got the old one for size comparisons, now start hunting for a similar size lawnmower engine flat muffler. Braze a flat plate on the back for the mounting holes maybe...I don't know what ytour exhaust looks like, only picked up one of them twice...
Would a real small old toasted cylinder from another saw maybe work, as something to start with, a l;ittle cutting and dremel work? I mean, is it an absolute that it has to be steel?? Cut it down, install sideways with a plate or something? Just thinking out loud, I love cob jobbing stuff....a finned muffler..sharp.....
Of course I can only lu####lly dream of owning a 3120, so maybe my ideas aren't real practical on such a valuable saw and you should just suck it up and buy a new muffler, then go cut one cord and sell it to pay for it....heck, a lot of areas of the country a half a cord goes for a benjamin...
vw_motorsports
ArboristSite Guru
Need husky 50 intake, before air injection
Need the intake partition for a husky 50 without the air injection...my 50 does not have the boss cast in the case to accept the air injection tube. It's the only thing I need to finally get this saw running.
please PM
thanks
BTW, want to thank MASTERMIND for helping me on my poulan...thanks U da MAN!
Need the intake partition for a husky 50 without the air injection...my 50 does not have the boss cast in the case to accept the air injection tube. It's the only thing I need to finally get this saw running.
please PM
thanks
BTW, want to thank MASTERMIND for helping me on my poulan...thanks U da MAN!
Thanks a lot Will. I found a good deal on feebay. It's on the way.
I am in need of a wrap handle for an 026. Cash, trade.......
Will the handle off an 028 work or be the same?
Mastermind
Work Saw Specialist
Not even close. I do appreciate you thinking about it though!
I've got one on the way fellows.
Not even close. I do appreciate you thinking about it though!
I've got one on the way fellows.
OK on that. A neighbor brought me a basket case 028 in a box.
Mastermind
Work Saw Specialist
I would like to have the whole saw if it's fairly complete.
srcarr52
We can't stop here, this is bat country.
Need the intake partition for a husky 50 without the air injection...my 50 does not have the boss cast in the case to accept the air injection tube. It's the only thing I need to finally get this saw running.
please PM
thanks
BTW, want to thank MASTERMIND for helping me on my poulan...thanks U da MAN!
Got you covered. PM sent!
deereguy
ArboristSite Operative
Help! Need an Crank for MS441
The crank on my Stihl MS441 broke off on the clutch side. Anyone have a used one? If yes, tell me what you are looking for in green or trade. rick 360-426-7245
The crank on my Stihl MS441 broke off on the clutch side. Anyone have a used one? If yes, tell me what you are looking for in green or trade. rick 360-426-7245
PB
Addicted to ArboristSite
Looking for a few things:
Jonsered 2163, 2165, 2171 carcass or lower end.
Jonseresd 2159/2156 fuel tank
Willing to trade:
Solo 635 (92cc)
I have some 2156 parts
Husky 357XP fuel tank and loop handle
Or I also have cash.
Send me a PM.
Jonsered 2163, 2165, 2171 carcass or lower end.
Jonseresd 2159/2156 fuel tank
Willing to trade:
Solo 635 (92cc)
I have some 2156 parts
Husky 357XP fuel tank and loop handle
Or I also have cash.
Send me a PM.
Jon1212
Riff Raff Fart Knocker from other Forum's.
Sachs Dolmar 100
Still looking for a chain brake assembly, clutch cover, and oil cap. I have crupled green paper for trade.
Still looking for a chain brake assembly, clutch cover, and oil cap. I have crupled green paper for trade.
How in the world did that happen? Of seriously doubt you'll find a used one.
SawGarage
Addicted to ArboristSite
hmmm... I want to assume the obvious...BUT, I'm not going to say it outloud...... :monkey:
Are you thinking impact gun? I doubt thats what it was.
I will take a picture of what is there. Might take me a couple of days though. Things been kind of strange around here lately. The handle assembly is broken so it is far from complete as that is what the neighbor took off it. I did see a carb in the box and the motor turns freely. Not sure of cyclinder condition.
Eccentric
Mister Wizard
Somebody mentioned those rim/drum 25DA setups here a while ago. IIRC, they took an oddball rim. That won't work on my 1.9/XX either from what I understand. That's a good deal on that bar. I'll probably get some kind of cheap-o deal from Baileys when I swap that saw over to 3/8LP (if I don't end up trading with Mark). Was just offering to help Mark out since I have a 1/4" pitch bar and chain for these saws and he seems to want one...
deereguy
ArboristSite Operative
Broken crank on a MS441
Brad/ Sawgarage, I picked the saw up yesterday and took it apart this morning. In order to press the crank out on the clutch side I had to grind flatten where the crank broke off. I was surprised on how soft the shaft material was (really soft) . My experience with stihl cranks is they are much harder than this one. Also, the clutch bearing was dry and hard to get off the shaft. I agree that I'll have a tough time finding a replacement crank. rick
Brad/ Sawgarage, I picked the saw up yesterday and took it apart this morning. In order to press the crank out on the clutch side I had to grind flatten where the crank broke off. I was surprised on how soft the shaft material was (really soft) . My experience with stihl cranks is they are much harder than this one. Also, the clutch bearing was dry and hard to get off the shaft. I agree that I'll have a tough time finding a replacement crank. rick
