Swap meet...

[epicklein22]

Your 372 top covers: are they tall or short, for the HD or standard air filter?

Short

 

[Harzack223]

359 parts

Hello all, I just picked up a husky 359 and am looking for a muffler and chain break cover. possibly a 20in bar for it as well.

I have some stihl stuff to trade or possibly cash. mostly for the smaller stihl stuff. maybe even get ride of my poulan 3400.

 

[outdoorlivin247]

Working on Jonsereds 70e and need front and rear handles...Also could use a plug cover, muffler and a front hand gaurd...

 

[yo2001]

possible trades,

026, one of the newer one with plastic handle. The plastic is faded. The compression little over 170 psi after cleaning the cylinder and piston. Need a recoil and clutch springs need to be replaced. Cranks and runs. (I used my recoil off another 026 to test.) The saw must have been left out after a coil went dead. (I replaced it)

Homelite Super EZ auto. The saw cranks and runs on and off. The compression was around 175psi last time I checked. I think it need a carb kit. It does have a real good spark.

Poulan Micro Deluxe XXV. It need a fuel line. I really haven't mess with it much.

Have a John Deere/ Homelite J3836r, needs a coil. Looks new with a case.

Mac 3818, Seems to have compression but needs a primer. I haven't realy mess with this either.

Also still have ms280 and 034 (needs a fuel line) too. thanks

Some pics of the saws.

 

[Work Saw Collector]

Some pics of the saws.

I'm sure I misreading your post what are you looking for in trade or $.

 

[yo2001]

Sorry I did not make the clear. I would like something bigger than 70cc saw. I don't mind tinkering with it. Or milling setup. I'm up for any trade though.

I'll keep the cash offer for pm's. Thanks

 

[dragrcr]

need an 044 tank/handle assembly

 

[Meadow Beaver]

Im looking for a decent running condition Homelite 990G if anyone has one to trade or sell.

 

[heimannm]

Working on Jonsereds 70e and need front and rear handles...Also could use a plug cover, muffler and a front hand gaurd...

I don't have the 70E IPL's but I have the parts from a 621 if they will work. PM me if you are interested. The loop handle on the 621 is grey rather than black.

Mark

 

[heimannm]

I am looking for the front handles (half wrap and full wrap) for McCulloch 10 Series saws, 5-10, 7-10, 10-10 etc.

I have a lot of McCulloch parts (new & used) as well as cash if needed.

Mark

 

[jockeydeuce]

Need a Homelite XL12 coil

Does anyone have a good electronic coil/module for a Homelite XL12???

I have some Stihl 038, 046 & 064 parts if someone needs something of equal value.

 

[Bowtie]

Does anyone have a good electronic coil/module for a Homelite XL12???

I have some Stihl 038, 046 & 064 parts if someone needs something of equal value.

pm sent.

 

[stihlboy]

possible trades,

026, one of the newer one with plastic handle. The plastic is faded. The compression little over 170 psi after cleaning the cylinder and piston. Need a recoil and clutch springs need to be replaced. Cranks and runs. (I used my recoil off another 026 to test.) The saw must have been left out after a coil went dead. (I replaced it)

Homelite Super EZ auto. The saw cranks and runs on and off. The compression was around 175psi last time I checked. I think it need a carb kit. It does have a real good spark.

Poulan Micro Deluxe XXV. It need a fuel line. I really haven't mess with it much.

Have a John Deere/ Homelite J3836r, needs a coil. Looks new with a case.

Mac 3818, Seems to have compression but needs a primer. I haven't realy mess with this either.

Also still have ms280 and 034 (needs a fuel line) too. thanks

yo your ms280 and 034 are sold "money in mail"

 

[Bill G]

Im looking for a decent running condition Homelite 990G if anyone has one to trade or sell.

So am I I sure wish they were around.

Bill

 

[wgrassel]

I have for trade a good running McCulloch ProMac 10-10. Later model with a working chainbrake and the integrated "muffler cover". According to the serial # and Acres site it should have electronic ignition (although I haven't looked). I bought the saw a year ago from the original owner. 150 psi compression the last time I measured. I put in a carb kit and a new fuel line. 16" McCulloch bar and Carlton safety chain with at least half its life left. The is a small gas leak from underneath the tank when the saw is running that I have not yet investigated. Other than that this is a good working saw. Starts easily and cuts fine.

I would like to trade for a 24" bar and chain(s) for my McCulloch PM610. I also just acquired a Mac 110 with a 14" bar that I would be interested in getting some extra chains for.

I live in Pittsburgh and travel frequently to Erie. It would be nice if we could work out a swap without need to ship, but I would be willing to pack and ship if necessary.

 

[PA452]

Don't have much to trade, but I just acquired a non-running Stihl 032AV. In particular I need a muffler, but I could potentially be interested in a number of replacement parts.

Anyone have anything available? Thanks

 

[wigglesworth]

Comes with original hardnose bar, original chain with the cardboard sleave it came in, original manual, and original hardcase. Very low use, prob just a tank or two. Nice little saw. Runs great.

I need a full wrap handlebar for a MS 460, a clutch for an MS 460, a full wrap for an 038 mag, A set of large dawgs for an 038, a 20" ES bar or will sell it outright. Make an offer via PM.

 

[caddguy]

Want a 066 or 660...trade for completely rebuilt 044 and computer and Other tools!

Ok. I have a really nice running 044 with 52mm BB kit installed. I bought this saw toasted and dropped from a tree. I have invested about 400.00 in parts for this saw and rebuilt from the ground up, new 20" Windsor bar and chain. Runs flawlessly, just dropped a soft maple with it so I think it's all broke in now...hehe.
I really want a 66 class saw as I have 80 acres of land to take care of.
I don't want to fork out the cash for a new 66 and I have always wanted a 66. Wife says fine but I don't need 2 saws laying around...she wears the pants
I have a really nice computer I could throw in and maybe even a few other tools to get what I am after......but I really am hoping a saw trade will get me there.
Anyone got an extra 66 class saw..cmon all you CAD guys!!

Best regards,
Dave

Pic of saw:

 

[cbolyard]

I've got an 064 chainbrake handle that was on my MS460 project when I bought it. Good condition, just a little heat damage from the muffler but no cracks. Looking to trade for an 046/460 chain brake handle, or oil pump with the washer that goes between the oiler and clutch.

 

[cbolyard]

need an 044 tank/handle assembly

I have an MS440 tank/handle, in good shape with no cracks or breaks.